Question

Q-4 Synchronous Motor Drives (10 Marks) The synchronous motors can be classified into six types, what are they?

Thumb for your efforts

0 0
Add a comment Improve this question Transcribed image text
Answer #1

different types of synchronous motors are -

1. Cylindrical Synchronous Rotor

2. Salient Pole Synchronous Rotor

3. Hysteresis Synchronous Motor

4. Reluctance Synchronous Motors

5. Permanent Magnet Synchronous Motors

6. DC Current Excited Synchronous Motors

Add a comment
Know the answer?
Add Answer to:
Thumb for your efforts Q-4 Synchronous Motor Drives (10 Marks) The synchronous motors can be classified into six types, what are they? Q-4 Synchronous Motor Drives (10 Marks) The synchronous mot...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • (b) (i) Explain briefly why an induction motor can never run at synchronous speed? (2 Marks)...

    (b) (i) Explain briefly why an induction motor can never run at synchronous speed? (2 Marks) (ii) If a six-pole induction motor supplied by a three-phase 50 Hz supply has a rotor frequency of 2.3 Hz, Calculate: (a)The percentage slip (b)The speed of the rotor in rpm (4 Marks) (iii)Draw a typical torque versus slip characteristic curve of an induction motor. If rotor resistance is increased show how the new torque versus slip curve deviates from the original one. (4...

  • Question 4 (10 marks) A) A 10-kVA, 415-V, three phase, Y -connected synchronous generator has a...

    Question 4 (10 marks) A) A 10-kVA, 415-V, three phase, Y -connected synchronous generator has a winding resistance of 0.3 Q and a synchronous reactance of 0.6 on a per phase basis. Determine its voltage regulation at full load when the power factor is (a) 75% lagging and (b) 75% leading. B) (10 marks) A 220-V, Y-connected, three-phase, synchronous motor has a synchronous reactance of 4 O/phase and negligible armature winding resistance. At a certain load the motor takes 7.5...

  • Question 4 [25 marks] An electric motor drives a coaxial rotor through a single-plate clutch which...

    Question 4 [25 marks] An electric motor drives a coaxial rotor through a single-plate clutch which has two pairs of driving surfaces each 300 mm external and 175 mm internal diameter. The variation of normal pressure with radius is given by a + b/r Pa and the maximum pressure is 150 kPa. The spring force on the system is 500 N. The mass of the motor armature and shaft is 750 kg and its radius of gyration is 240 mm;...

  • Question 2 [10 marks) A six pole, three phase induction motor, with a star connected stator...

    Question 2 [10 marks) A six pole, three phase induction motor, with a star connected stator winding is energised from a 380V, 50Hz supply. The ratio of the stator to rotor turns is assumed 1.8 and a full load slip of 4%. If the respective per phase rotor resistance and standstill reactance are 0.120 and 0.8502, determine: a. Torque developed at full load b. The maximum torque and the speed at maximum torque

  • Question (3) Speed Control [10 Marks A 50 hp, 220 V, 1500 rpm DC shunt motor...

    Question (3) Speed Control [10 Marks A 50 hp, 220 V, 1500 rpm DC shunt motor with an armature resistance of 0.04 Q and a field resistance of 50 Q. The motor has compensating windings, so armature reactance can be ignored. Mechanical and core losses may be ignored also. The moter is driving a load toque that is proportional with speed, Ti a (n). The motor is driving a load with a line current of 80 A and an initial...

  • answer asap plz will thumb up Question 9 (10 points) There are basically 4 layout types...

    answer asap plz will thumb up Question 9 (10 points) There are basically 4 layout types used in organizing the work flow for manufacturing processes. They are: Fixed-Product Layout, Flowline/Product Layout, Cellular/Group Technology Layout, and Process/Functional/Job Shop Layout. A flowline/product layout has which of the following characteristics? a) Sometimes can be the preferred layout when high levels of precision are in order O b) The line for each part is organized in a way that facilitates the corresponding production flow....

  • Question 4: (25 marks) There are different types of auditor opinions, one of which they must...

    Question 4: (25 marks) There are different types of auditor opinions, one of which they must express in their audit report once they will complete their audit process. List and briefly discuss the different types of auditor opinions.                                                                                                                         (15 marks) Identify that under following cases what types of opinions can be expressed by the auditor? Support your answer with discussion.                                                                                                                                                                                                             (10 marks) Case A The auditor noticed that inventory of Alpha Company faces a write-down due...

  • Assume the production function is q = f(h, k) = 2n12 a) (4 marks) What is...

    Assume the production function is q = f(h, k) = 2n12 a) (4 marks) What is the marginal product of labor (M Pn)?- b) (4 marks) What is the marginal product of capital (M Pk)?4 c) (8 marks) Assume p = 2, w = 1/2, and r = 3. Calculate the profit maximizing level of labor demand (h*). – d) (6 marks) If w increases to w = 3 (and p and r stay at p = 2 and r=...

  • Q-1 What is irreversibility in a power plant, what are types of irreversibility?

    Q-1 What is irreversibility in a power plant, what are types of irreversibility?Q-2 What is a pinch point? What is its effect on the size and efficiency of the steam generator?Q-3 What is the mean temperature of heat addition? What is its effect on cycle efficiency? Explain the different methods by which the mean temperature of heat addition can be increased.Q-4 How is the maximum and minimum pressure of a steam cycle is decided - How can we address the...

  • Question 1 2) Manufacturing processes can be classified into 2 (Two) major groups. Briefly describe the...

    Question 1 2) Manufacturing processes can be classified into 2 (Two) major groups. Briefly describe the characteristics of each group. Aid your answer with hierarchy. (10 marles) 1) Sand casting is a process for casting metal in sand molds. Explain FIVE (3) sand casting benefits to the industry (marks) Riser, also known as feeder, is an important part in a sand mold. Briefly describe the function of a riser in a sand casting mold Hence, illustrate the possible types and...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT