PROCEDURE 1. Prepare three 100 mL beakers for this experiment. Use the molecular weights on the bottles to calculate the amount of solid to use. a. *b. Prepare 25 mL of a 10 M NaOH solution (concentr...
Prepare 250 mL of-0.02 M K2Cr2O7 by transferring an accurately weighed amount of the dried dichromate into a 250 mL volumetric flask and diluting to the mark. Since this is a volumetric preparation, the exact concentration of the titrant will be based on the analytical weight of the potassium dichromate used to prepare the solution. . Analysis of the Unknown FeO Sample Accurately weigh four (4)-0.3 g samples of the dried unknown into four 400 or 600 mL beakers. Add...
4. Calculate the volume of 1 M sodium hydroxide (NaOH) needed to prepare 10 ml of a 0.10 M sodium hydroxide solution. 5. Calculate the volume of 1 M hydrochloric acid (HCI) needed to prepare 10 mL of a 0.10 M hydrochloric acid solution. 6. Determine the volumes of 0.10 M CH3COOH and 0.10 M CH3COONa required to prepare 10 ml of the following pH buffers. (Note: the pka of CH3COOH =4.7) C. pH 3.7 b. pH 47 C. pH...
Calculate the amount of heat energy, q, produced in each
reaction. Use 1.03 g/mL for thedensity of all solutions. Use the
specific heat of water, 4.18 J/(g•°C), for all solutions.
The temperature change in part 3 was 15.5 degrees celsius.
Temperature change in part 4 was -1.2 degrees celsius.
Then determine the enthalpy change for each reaction in terms of
kJ/mol of each reactant.
The molarity of NaOH is 2.0 M.
Part III Conduct the Reaction Between Solutions of NaOH...
I don't understand what calculations I would have made to create
the buffer solution from Part D of the lab. I understood the
procedures I took to create the solution but when the report asks
to show the calculations used to prepare the buffer solution I am
not sure other than mixing the volumes indicated in the procedures
section.
Thank you
pH of Butter Assigned by Instructor 5.12. Measured pH of Assigned B r .9 (Read the procedural Show the...
To prepare 100 mL of 25 mM Tris buffer at pH 8.0, calculate the amount of Tris base and Tris·HCl needed to make the buffer. (Hint: find out the p K a of Tris·HCl and use the Henderson - Hassel Balch Equation) Describe how do you want to make the solution, including how much water to add, how to adjust pH, etc.
Post Lab Activity Acids, Bases, pH, and Buffers 1. Calculate the pH of a 0.08 M NaOH solution. 2. Hydrochloric acid is a strong acid and dissociate almost 100% in aqueous solution. If two drops (0.1 mL) of 1.0 MHCI are added to pure water to make 1.0 L solution. What is the pH of this solution? 3. M. What will be the A dilute solution of hydrochloric acid (HCI) has a concentration of 0.1 pH of this solution? 4....
Exercise 1. Lab Preparation. Q1) 25.00 ml of 0.10 M COCI, solution is needed for this experiment. Show all calculations associated with the creation of this solution. 25.00mil IL 10.10m Coch 100oment Timor coche 0.32g Colla Q2) Describe how to make 25.00 mL of 0.10 M CoCl, solution. Be specific. Prepare the solution. Add 0.32g of Collz in 25.com, of water to preport 0.70M Collz Solomon 93) Determine the amount of 1.00 M HCl stock solution needed to form 100...
question#1
Experiment 17A. A Solubility Product Constant Procedure Getting Started 1. Obtain a 10 ml pipet, a 50 mL buret, and 2 pieces of 120 cm filter paper Preparing Saturated Solutions of M10J MIO), is an insoluble divalent iodate salt. The identity of the cation M-is unknown. 1 Prepare MIO,), by adding S0 ml of o.2 M KIO, to 20 mL of 1 Molar M(NO,J, in a 150 mt 2. Stir the mixture vigorously with a stirring rod. A white,...
I
need it right now, please help me??
PROCEDURE PART I: DILUTING THE VINEGAR SOLUTION The vinegar solution must be diluted by a factor of 5 to be suitable for titration. 1. Obtain - 20 ml of the stock vinegar solution from the fume hood. 2. Using the 10-ml. pipet, pipet" 10 mL of the stock solution to a 50-ml volumetric flask. 3. Fill the volumetric flask to the calibration line with distilled water. Be sure not to go over...
can someone please answer number one? im so lost
DYES AND DYEING CHAPTER 1. Calculate the amounts of salicylic acid, 1-naphthol, 2-naphthol, 8-anilino-1-naph- thalenesulfonic acid ammonium salt, or N,N-dimethylaniline needed for Part 1B of this experiment (use molecules as assigned by your TA). 190mg 3-aminobenzene 2.5mL Sulfonic acid 2.5% sodium carbonate solution 81mg Sodium nitrate 2. What is the purpose of the sodium carbonate in Part 1A? Why do we add glacial acetic acid in Part 13 when we react...