Homework Answers
Add Answer to:
Please answer the following with all explanations Problem #3 A 1200/5, C400 CT is connected on the tap 1000/5. What is the maximum secondary burden that can be used and we can maintain rated accur...
Problem #1 A multi-ratio current transformer with the following ratios (1200:5, 1000/5, and 800:5) high permeability...
Problem #1 A multi-ratio current transformer with the following ratios (1200:5, 1000/5, and 800:5) high permeability silicon steel has a cross sectional area of 3.5 square-inches and a secondary resistance winding of 0.29 Ohms. The maximum current for which the transformer will operate is 35kA at 60 Hz. The relay burden including the leads is 2.2 Ohms. Using the formula method determine if the CT will saturate at the three given rations (CT saturation density)
Please answer the following with all explanation: Problem #2 what will be the approximate % error...
Please answer the following with all explanation:
Problem #2 what will be the approximate % error if a 500:5 class C CT is connected to a secondary burden of 2.5 Ohms and the secondary current is 68A
Please answer all of these questions with brief explanations. Thank you! Name: Doppler ultrasound PROBLEM 4-8...
Please answer all of these questions with brief explanations.
Thank you!
Name: Doppler ultrasound PROBLEM 4-8 points Ultrasound is the name we give to sound waves that have a higher frequency than 20 kHz, which is the maximum frequency our ears can respond to. For this problem, assume that high frequency sound waves travel through human tissue at 1500 m/s (about the speed of sound in water). 2 points] (a) Ultrasound equipment for diagnostic imaging typically uses frequencies between 1...
solve no: 3.14 , 3.16, 3.19 please show each step and solve for beginners 120 Power...
solve no: 3.14 , 3.16, 3.19
please show each step and solve for beginners
120 Power System Analysis 3.12. A single-phase system similar to that shown in Figure 3.11 has two transformers A-B a B-C connected by a line B feeding a load at the receiving end C. The ratings and parame ter values of the components are 500 V/1.5 kV, 9.6 kVA. leakage reactance 5 % 1.2 kV/120 V, 7.2 kVA, leakage reactance 4 % series impedance (0.5 +...
please use multisim to answer all the parts. EXPERIMENT 3 TESTING SERIES & PARALLEL RESONANCES Objectives:...
please use multisim to answer all the parts.
EXPERIMENT 3 TESTING SERIES & PARALLEL RESONANCES Objectives: To examine the conditions of resonances To observe the resonant circuit properties Equipment & components: A personal computer with Multisim software Preview questions: 1. How does the resonant frequency relate to the inductance and capacitance in a series LC circuit? 2. When the circuit in Figure 1 is tuned to resonant frequency, how does the voltage cross the resistor relate to the applied voltage?...
Can you please answer all my questions please. I really need the answers to all the...
Can you please answer all my questions please. I
really need the answers to all the questions please
ORC221F/101/3/2019 48. Which of the following statements about benzene is INCORRECT? (1) All twelve atoms do not lie in the same plane (2) All the carbon atoms are sp2 hybridized (3) The C-H bonds are all the same length (4) The electrophilic aromatic substitution reaction is a common reaction type 49. Name the following compound according to the IUPAC nomenclature. (1) N-ethyl-2-bromo-2-methyl-2-pentanamine...
Need help with schematics for blocks 3, 4 and 5!!!!!! Include all schematics and wiring along with the component values...
Need help with schematics for blocks 3, 4 and
5!!!!!!
Include all schematics and wiring along with the component
values and how you acquired them. Explain how each block functions
and label any figures.
Need schematics for blocks 3, 4 and 5!!!!!!
Goal For your final project you will be asked to design and assemble a system in which you will input a stereo audio signal, mix the channels into a single mono signal, amplify the signal, filter it to...
AND THE USE OF CALCULATORS SPREADSHEETS 2. PLEASE MAKE SURE TO WRITE Sttolal ANSWER EXPLANATIONS THAT...
AND THE USE OF CALCULATORS SPREADSHEETS 2. PLEASE MAKE SURE TO WRITE Sttolal ANSWER EXPLANATIONS THAT ARE SUPPORTED BY YOUR CALCULATIONS WHEN ASKED IN A GINEN QUESTION 3. PLEASE USE EXCEL TO CALCULATE AND SHow WORKINGS. THANKS. 2 Industrial Grinders AWN 4 During the term, we had a case study, Industrial Grinders, which focused on Sunk and Opportunity Costs. 6 Please refer to the table below, which comes from data in the Industrial Grinders case Industrial Grinders 100 Steel Rings...
Yes, this is one problem. Please solve ALL PARTS. Guaranteed thumbs up for the person who solves it. 3 1. Photodiode...
Yes, this is one problem. Please solve ALL PARTS. Guaranteed
thumbs up for the person who solves it.
3 1. Photodiode amplifier circuit You are designinga CF photosensor circuit for a light detection and ranging LiDAR) system in autonomous vehicles. The circuit utilizes a transimpedance amplifier to convert low-level RF photodiode current signal to a usable voltage output. It consists of a photodiode, an amplifier, and feedback capacitor/resistor pair as shown in Figure 1. We will derive simple equations to...
answer the questions based on the informations on the 3 pictures please: What are the essential...
answer the questions based on the informations on the 3 pictures
please:
What are the essential responsibilities of a structural
designer or engineer in designing a structure?
What factors would you consider and why when planning the
design of a building structure?
You are the project team leader for the design of a single
family house in southwest Houston area. Discuss the types of
structural loads you think are important and explain
why.
d) Thermal load changes in perature cause...
Problem #1 A multi-ratio current transformer with the following ratios (1200:5, 1000/5, and 800:5) high permeability silicon steel has a cross sectional area of 3.5 square-inches and a secondary resistance winding of 0.29 Ohms. The maximum current for which the transformer will operate is 35kA at 60 Hz. The relay burden including the leads is 2.2 Ohms. Using the formula method determine if the CT will saturate at the three given rations (CT saturation density)
Please answer the following with all explanation:
Problem #2 what will be the approximate % error if a 500:5 class C CT is connected to a secondary burden of 2.5 Ohms and the secondary current is 68A
Please answer all of these questions with brief explanations.
Thank you!
Name: Doppler ultrasound PROBLEM 4-8 points Ultrasound is the name we give to sound waves that have a higher frequency than 20 kHz, which is the maximum frequency our ears can respond to. For this problem, assume that high frequency sound waves travel through human tissue at 1500 m/s (about the speed of sound in water). 2 points] (a) Ultrasound equipment for diagnostic imaging typically uses frequencies between 1...
solve no: 3.14 , 3.16, 3.19
please show each step and solve for beginners
120 Power System Analysis 3.12. A single-phase system similar to that shown in Figure 3.11 has two transformers A-B a B-C connected by a line B feeding a load at the receiving end C. The ratings and parame ter values of the components are 500 V/1.5 kV, 9.6 kVA. leakage reactance 5 % 1.2 kV/120 V, 7.2 kVA, leakage reactance 4 % series impedance (0.5 +...
please use multisim to answer all the parts.
EXPERIMENT 3 TESTING SERIES & PARALLEL RESONANCES Objectives: To examine the conditions of resonances To observe the resonant circuit properties Equipment & components: A personal computer with Multisim software Preview questions: 1. How does the resonant frequency relate to the inductance and capacitance in a series LC circuit? 2. When the circuit in Figure 1 is tuned to resonant frequency, how does the voltage cross the resistor relate to the applied voltage?...
Can you please answer all my questions please. I
really need the answers to all the questions please
ORC221F/101/3/2019 48. Which of the following statements about benzene is INCORRECT? (1) All twelve atoms do not lie in the same plane (2) All the carbon atoms are sp2 hybridized (3) The C-H bonds are all the same length (4) The electrophilic aromatic substitution reaction is a common reaction type 49. Name the following compound according to the IUPAC nomenclature. (1) N-ethyl-2-bromo-2-methyl-2-pentanamine...
Need help with schematics for blocks 3, 4 and
5!!!!!!
Include all schematics and wiring along with the component
values and how you acquired them. Explain how each block functions
and label any figures.
Need schematics for blocks 3, 4 and 5!!!!!!
Goal For your final project you will be asked to design and assemble a system in which you will input a stereo audio signal, mix the channels into a single mono signal, amplify the signal, filter it to...
AND THE USE OF CALCULATORS SPREADSHEETS 2. PLEASE MAKE SURE TO WRITE Sttolal ANSWER EXPLANATIONS THAT ARE SUPPORTED BY YOUR CALCULATIONS WHEN ASKED IN A GINEN QUESTION 3. PLEASE USE EXCEL TO CALCULATE AND SHow WORKINGS. THANKS. 2 Industrial Grinders AWN 4 During the term, we had a case study, Industrial Grinders, which focused on Sunk and Opportunity Costs. 6 Please refer to the table below, which comes from data in the Industrial Grinders case Industrial Grinders 100 Steel Rings...
Yes, this is one problem. Please solve ALL PARTS. Guaranteed
thumbs up for the person who solves it.
3 1. Photodiode amplifier circuit You are designinga CF photosensor circuit for a light detection and ranging LiDAR) system in autonomous vehicles. The circuit utilizes a transimpedance amplifier to convert low-level RF photodiode current signal to a usable voltage output. It consists of a photodiode, an amplifier, and feedback capacitor/resistor pair as shown in Figure 1. We will derive simple equations to...
answer the questions based on the informations on the 3 pictures
please:
What are the essential responsibilities of a structural
designer or engineer in designing a structure?
What factors would you consider and why when planning the
design of a building structure?
You are the project team leader for the design of a single
family house in southwest Houston area. Discuss the types of
structural loads you think are important and explain
why.
d) Thermal load changes in perature cause...
Most questions answered within 3 hours.
-
how
does gravity affect the trajectory of projectile? what would be the
shape of the trajactory...
asked 14 minutes ago -
Two small plastic spheres are given positive electrical charges.
When they are a distance of 15.4...
asked 22 minutes ago -
An acidic solution containing gold ions is
electrolyzed, producing gaseous oxygen (from water) at the anode...
asked 37 minutes ago -
Assume that the population of Mexico is 128
million and that the population increases 1.01
percentannually....
asked 1 hour ago -
Can someone please help me add appropriate descriptive
comments to each line of code in the...
asked 1 hour ago -
Romeo wishes to throw a bouquet of flowers to Juliet, who is on
a second-story balcony,...
asked 2 hours ago -
Why is QE a controversial monetary policy tool.
A. It may lead to excessive inflation.B. By...
asked 2 hours ago -
Principles of Programming midterm study guide help!
1.)
______ Which of the following would reference the...
asked 2 hours ago -
A finite potential well has depth U0 = 2.78 eV . What is the
penetration distance...
asked 3 hours ago -
1. The bus bars of a power station are in two sections A and B
separated...
asked 3 hours ago -
Fiscal policy is the deliberate manipulation of taxes and
government spending to alter GDP, employment, inflation...
asked 4 hours ago -
evaluating an expression using only one digit and + and - as
operators ....3+5-1+7-5+8
-----------------------
stack...
asked 4 hours ago