please solve this question using excel sheet (refrigeration systems) Q1): It is required to design a condenser that will be suitable for a refrigeration system that uses refrigerant 22 as the wo...
please provide excel sheet for the calculation too
Q1): It is required to design a condenser that wl be suitable for a refrigeration system that uses refrigerant 22 as the working fluid. The refrigeration system provides a refrigerating capacity of 50 kW for air conditioning purposes. At design conditions, the condensing temperature is 40°C while the evaporating temperature is 0°C. Cooling water enters the condenser at 25°C and leaves at 30°C. Design the condenser (calculate the required heat transfer area...
EXAMPLE 6 A household refrigeration system works with a vapor compression refrigeration system with two evaporators using Refrigerant 134a as the working fluid. This arrangement is used to achieve refrigeration at two different temperatures with a single compressor and a single condenser. The low temperature evaporator operates at -18°C with saturated vapor at its exit and has a refrigerating capacity of 10.5 kW (3 tons). The higher- temperature evaporator produces saturated vapor at 3.2 bar at its exit and has...
Problem 10.008 SI Refrigerant 22 enters the compressor of an ideal vapor-compression refrigeration system as saturated vapor at -30°C with a volumetric flow rate of 5 m/min. The refrigerant leaves the condenser at 19°C, 9 bar. Determine: (a) the magnitude of the compressor power, in kW. (b) the refrigerating capacity, in tons. (c) the coefficient of performance. (d) the rate of entropy production for the cycle, in kW/K. Part A Determine the magnitude of the compressor power, in kW. W....
Q1/ Figure 1 shows a refrigeration system of multi evaporators and single compressor using R407C as refrigerant. The evaporators provide cooling capacity of 10 and 20 TR at temperatures of -10 °C and 10 °C respectively. The system provided with multi ex valves (the multi expansion valve advantage is that the refrigerant that enters the low temperature evaporator expansion valve is saturated liquid and the flash gas is removed at poirnt 4). The condenser temperature is 50 °C. Calculate the...
A vapor-compression refrigeration system which operates on the cascade cycle arrangement shown below is used to obtain refrigeration at a low temperature. Refrigerant-12 is the working fluid in the high-temperature cycle and Refrigerant-13 is used in the low-temperature cycle. For the Refrigerant 13 cycle, the working fluid enters the compressor as saturated vapor at -30°F and is compressed isentropically to 250 lbf/in2. Saturated liquid leaves the intermediate heat exchanger at 250 lbf/in2 and enters the expansion valve. For the Refrigerant...
QUESTION 4 (15 marks) Below is a schematic of a car air conditioning system that uses R-134a as its refrigerant. Here we will analyze the system under the case of driving through a very hot environment of 40 °C. The interior of the car is kept at 20 °C. Refrigerant leaves the compressor at 1.6 MPa absolute and leaves the condenser as a saturated liquid. The evaporator operates at 400 kPa absolute and the refrigerant leaves as a saturated vapour....
1.3 127 5.3 3.(10 pts) A cold storage room (10 m x 10 m x 10 m) is being maintained at 2 °C using a vapor compression refrigeration system that uses R-134a. The evaporator and condenser temperatures are -20 and 40°C, respectively. The walls and ceiling of the storage room is constructed of 15 cm thick concrete (thermal conductivity-1.37 WIm K]) and 4.3 cm thick insulation (thermal conductivity-0.04 W/[m K). The outside insulation surface temperature of the walls (or ceiling)...
System Model: Automotive Air Conditioning System Outside Air Temp: 45 oC Car Interior Air Temp: 22 oC Heat Load = 4.2 kJ/sec rate at which heat must go in to the air conditioner to be removed from the car’s interior Refrigerant: R134a HINT: Heat enters an air conditioning system where? Refrigerant 134a … - leaves the evaporator coil and enters the compressor as a saturated vapor at the evaporator pressure of 2.8 bars. - It leaves the compressor at...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...