Using Cisco Packet Tracer (PT) create a topology with EIGRP (Enhanced Interior Gateway Routing Protocol) as routing protocols, using 4 switches. Show steps.
If any problem in understanding please comment below.
Here is the step by step process.
1. First take 4 routers, 4 switches and pc's .
2. I connected the devises in bus topology.( Make connections between router ,switch and pc's).
3.For pc assign ip address as shown in fig by click on pc>>desktop>>ip configuration>>static
4. Assign ip address to router i.e assign connected network address . Router>>config>>fastethernet0/0 to assign address to network.
Router>>config>>Serial2/0 to assign address to network between router to router.
5. Configure EIGRP to each router.
Configure EIGRP to all routers and assign ip to all pc's along with default gateway to all pcs as described above.
Now message can be sent and received.
Message has been send from pc0 to pc4 and reply delivered to pc0
Using Cisco Packet Tracer (PT) create a topology with EIGRP (Enhanced Interior Gateway Routing Protocol) as routing protocols, using 4 switches. Show steps.
Using Cisco Packet Tracer (PT), create a topology with 5 routers using OSPF (Open Shortest Path First) for a basic network (any kind will do) and show steps.
Design a Static router configuration using Cisco Packet tracer to configure the router manually by adding routes in routing table Build a network topology with 3 Routers, 3 Switches and 10 P.C’s each switch has server with DHCP enabled. please upload and send the link.
interior gateway protocol periodically sends routing information (TCO 4) The to just its neighboring routers. Open Shortest Path First (OSPF) Routing Information Protocol (RIP) Border Gateway Protocol (BGP) Reverse Path Forwarding (RPF) none of the above
Using Cisco Packet Tracer, do the following. Your submission should clearly give all CLis in each case and illustrate (a) through (e) through screen captures. (a) Create a network topology with two switches SWO and SW1. SWO should connect four devices i.e., two computers PCO and PC1 and two printers P1 and P2. SW1, on the other hand, connects computers PC2 through PCS and a DHCP server SO. (b) Configure the connection in (a) so that all devices get their...
Configure RIPv2 1. Create the following network topology on Packet Tracer 192.168.2.0/30 192.168.2.2 /30 192.168.2.1/30 192.168.1.1/25 1811 R1 281 192.168.1.129/25 1192.168.1.128 /25 192.168.1.0/25 PC-PT PC1 PC-PT PC2 192.168.1.254/25 192.168.1.126/25 2. Configure the PCs and the routers with network information based on their networks. To configure the routers, use the CLI rather than through the GUI Router1: Fa0/0 192.168.1.1 255.255.255.128 Serial 192.168.2.1 255.255.255.252 with clock rate of 64000 Router2: Fa0/0 192.168.1.129 255.255.255.128 Serial 192.168.2.2 255.255.255.252 Completed 4. Now apply RIPv2 to...
PLEASE ATTACH A SCREENSHOT OF YOUR SUCCESSFUL PING IN PACKET TRACER FOR THE END!!!!!!!!!!! THANK YOU! Objectives Part A: Configure a simple static routing . Part B: Configure a simple RIP routing Part A: Configure a simple static routing 1. Create the following network topology on Packet Tracer Router-PT Router-PT Addressing Table Device Interface IP Address Subnet Mask Default Gatewa 10.0.0.1 20.0.0.1 30.0.0.1 20.0.0.2 0.0.0.10 30.0.0.10 N/A 255.0.0.0 255.0.0.0 255.0.0.0 255.0.0.0 255.0.0.0 255.0.0.0 Routero 2/0 NIA NIA NIA 10.0.0.1 30.0.0.1...
1) How to Create VLAN on Cisco Catalyst Switch #show vlan а. VLAN Name Status Ports 1 default active Gil/0/1, Gil/0/2, Gil/0/3, Gil/0/4 Gil/0/5, Gil/0/6, Gil/0/7, Gil/0/8 config t Interface vlan 20 b. interface range gigabitEthernet 0/1 - 6 switchport access vlan 20 exit c. #show vlan VLAN Name Status Ports 1 default Gil/0/1, Gil/0/2, Gil/0/7, Gil/0/8 Gil/0/3, Gil/0/4, Gil/0/5, Gil/0/6 active active 20 VLAN020 2. How to Delete VLAN on Cisco Catalyst Switch no vlan 20 a. b. show...