Assume: width (in)= 2
thickness (in)= 0.25
force (ib)= 500
pin diameter (in)= 0.5
Homework Answers
Add Answer to:
Assume: width (in)= 2 thickness (in)= 0.25 force (ib)= 500 pin diameter (in)= 0.5 4. See the pin joint shown below, the...
assume: width (mm)= 30 overlap (mm)= 21 glue strength (n/mm^2)= 1 3. See the double lap joint shown below. Assume that...
assume:
width (mm)= 30
overlap (mm)= 21
glue strength (n/mm^2)= 1
3. See the double lap joint shown below. Assume that the plates at the joint are connected using an epoxy having a shear strength between 1.0 and 2.5 N/mm2 and the entire overlap is glued. a. Given the width of the plates and length of overlap from the spreadsheet, what is the shear stress in the epoxy? b. What is the minimum area of overlap given the strength of...
A shaft with a diameter of 43 mm, is shown below On the right hand side...
A shaft with a diameter of 43 mm, is shown below On the right
hand side at location D a wheel has a force F of 4824N applied. The
diameter of this wheel is 150 mm. The torque produced by F is
transmitted through the entire shaft to location A where the torque
is reacted. There are no other constraints at location A. Bearings,
are located at B and C, and provide radial constraint. The bearing
at B also provides...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
You are the designer and you have been asked to design a speed reducer (gearbox) that will take p...
power = 3 kW
if need any more information please ask !!!
You are the designer and you have been asked to design a speed reducer (gearbox) that will take power from the shaft of an electric motor rotating at 1500 rpm and deliver it to a machine that is to operate at approximately at 200 rpm Assume that you have decided to use spur gears to transmit the power [A power equal to the last one digits of your...
assume:
width (mm)= 30
overlap (mm)= 21
glue strength (n/mm^2)= 1
3. See the double lap joint shown below. Assume that the plates at the joint are connected using an epoxy having a shear strength between 1.0 and 2.5 N/mm2 and the entire overlap is glued. a. Given the width of the plates and length of overlap from the spreadsheet, what is the shear stress in the epoxy? b. What is the minimum area of overlap given the strength of...
A shaft with a diameter of 43 mm, is shown below On the right
hand side at location D a wheel has a force F of 4824N applied. The
diameter of this wheel is 150 mm. The torque produced by F is
transmitted through the entire shaft to location A where the torque
is reacted. There are no other constraints at location A. Bearings,
are located at B and C, and provide radial constraint. The bearing
at B also provides...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
power = 3 kW
if need any more information please ask !!!
You are the designer and you have been asked to design a speed reducer (gearbox) that will take power from the shaft of an electric motor rotating at 1500 rpm and deliver it to a machine that is to operate at approximately at 200 rpm Assume that you have decided to use spur gears to transmit the power [A power equal to the last one digits of your...
Most questions answered within 3 hours.
-
14. Which of the following statements is correct?
a. The probability of Type II error is...
asked 10 minutes ago -
A piano has been pushed to the top of the ramp at the back of a...
asked 9 minutes ago -
What is the pH of a 3.3 x 10^-7 M NaOH solution? [_____________]
= pH
Please...
asked 8 minutes ago -
The salt copper(II) sulfate is soluble in
water. When 2.19 g
CuSO4 is dissolved in
102.00...
asked 24 minutes ago -
When light is incident
upon the interface between two refractive media such that the angle
of...
asked 24 minutes ago -
Q2. (4 pts) A certain microprocessor
(uP) has a 37-bit address bus and a 32-bit wide...
asked 37 minutes ago -
Research a species currently considered endangered. Detail the
general biology of this species, what
type of...
asked 38 minutes ago -
Identify three challenges of using images in multimedia
documents and explain how each challenge is overcome.
asked 43 minutes ago -
The combined math and verbal scores for students
taking a national standardized examination for college admission,...
asked 46 minutes ago -
The position of a car as a function of time is given by
x=(45m)+(−5.5m/s)t+(−8m/s^2)t^2.
a. What...
asked 49 minutes ago -
0.200 moles N2O4 were placed in a 2.00-L container, and at
certain temperature the equilibrium set...
asked 1 hour ago -
The market with demand function Q = 800 4p is supplied by a
single firm with...
asked 1 hour ago