Question

R1 R2 100Ω 100Ω LM358N V1 R3 R4 100Ω 174Ω V5 LM358N

op amp LM358N is used. This device is actually temperature measurement. Instead of resistor of 174Ohms, it should be a RTD or PT100, but I don't have in the lab right now, so this is simulation. With this resistance, temperature should be around 188-189 Celsius. I hope this part is clear. In the lab, for different temperatures I will put different resistor, 190 Ohms, 280 Ohms etc. Output of the amplifiers should be connected to pins A0 and A1 on Arduino Mega board. The task is for different resistance to get appropriate temperature, according the table (in this case, table for pt100 is used).5 volts are coming from Arduino, and that 5 volts are connect to the power supply of the bridge, and also for the amplifier.Ground is going on Arduino too. I don't know how to code this circuit in Arduino. If you can help, it will be good. Thank you.

0 0
Add a comment Improve this question Transcribed image text
Answer #1


(1-osz) (t-oszヴ (1-0.r. ( s-2) (05) (1-0 ) 2:2 (1(0 1)(1) 3 C1-0 5 c- Sh) -$66) -25/3 (リ → (152)Ci-02 1-0.82 T) formula

Add a comment
Know the answer?
Add Answer to:
op amp LM358N is used. This device is actually temperature measurement. Instead of resistor of 174Ohms, it should be a...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • I am working on my Physics lab report where it was all about Direct Current Measurement...

    I am working on my Physics lab report where it was all about Direct Current Measurement and Ohm’s Law. We had 5 different resistors and had to construct different circuits using a power supply, volt-ohm-milliammeter (VOM) and a digital multimeter to get measurements of resistance, voltage, and current. Nominal values of resistance and tolerance Resistor Nominal Resistance (Ohms) Tolerance (Ohms) R1 680 +/- 68 R2 1000 +/- 50 R3 1500 +/- 75 R4 4700 +/- 470 R5 10,000 +/- 500...

  • Need help with conclusion questions please 1. The objectives of this lab are (1) to determine...

    Need help with conclusion questions please 1. The objectives of this lab are (1) to determine the actual (A) total resistance of three resistors connected in series and compare it with the experimental (E ) value of total resistance (2) to determine the actual (A) total resistance of three resistors connected in parallel and compare it with the experimental(E ) value of total resistance II. Apparatus(Equipment): Voltage source, ammeter that measures current , voltmeter that measures voltage. II. Procedure: Three...

  • In this Lab you would connect resistors in various combinations then use the multi- meter to...

    In this Lab you would connect resistors in various combinations then use the multi- meter to measure various currents and voltages. I have copied the schematics of the various circuits from the lab and completed portions of the data table with hypothetical (but highly probable) answers. Your task is to complete the data tables and answer the following questions. The value of a resistor can be determined by reading the colored stripes on the resistor. The color codes are given...

  • EE 282-Circuit I Pre-Lab 9 Maximum Power Transfer Theorem Name Concepts: In this pre-lab we will ...

    EE 282-Circuit I Pre-Lab 9 Maximum Power Transfer Theorem Name Concepts: In this pre-lab we will be leaming about Maximum Power Transfer Theorem. Maximum power is transferred to the load when the load resistance equals the thexenin equivalent, and we carry out the analysis using Thevenin's equivalent circuit. In order to do this, first build the following circuit on Mutism. 1 R1 5.1k0 R3 2 V1 R2 8kQ 6.8㏀ Fig. 1 Part 1: To find the Thevenin equivalent resistance, we...

  • please help with problems 7 and 8, I am extremely confused! Part 2: Kirchhoff's Rules For...

    please help with problems 7 and 8, I am extremely confused! Part 2: Kirchhoff's Rules For the circuit shown below, the directions of the currents through the circuit elements has been chosen arbitrarily. Using Kirchhoff's rules, you will determine the actual currents through the circuit elements. (Yes, this circuit could be analyzed using equivalent resistance, but don't do it that way.) R1: 752 Kirchhoff's Junction Rule 4) Start by choosing a junction. Write Kirchhoft's Junction rule for that junction below...

  • I only need help with the discussion there are many info that you do not need put I put just in ...

    I only need help with the discussion there are many info that you do not need put I put just in case as well as my data table. please do it as soon as u can Meauements ODeit1 Check2 Meaurements Checi3 Ced Check5 Check6 Measurements Check7 heck8 4058 33 536 1502 1035 979 119478 041 1.0319|0.554972| 64261| 153|15542033681 995781 5266566 1578807 298h 1631 119 1209430016 079096812 0.418135246 0,00032665 011890:004668155728441 0293237 1.291809502 1.22833 1.28 1952 -1116 4281 140616885511984206317 3346 8162 0.78...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT