College Of Engineering wsialdul University ofBusiness and Tochmoloty Collage of Engineering CE 313 Basie Structural...
Question 1: Calculate the reactions at all supports and determine the force in members CD, DE, FE, FC, and BC and state whether they are in tension or compression. 11 KN 16 kN 16 KN 20 KN 1.5 m- Mem ber CD DE FE FC BC Force Type
Question 1: Calculate the reactions at all supports and determine the force in members CD, DE, FE, FC, and BC and state whether they are in tension or compression. 11 KN 16 kN 16 KN 20 KN 1.5 m-
AC-CD- BC Exercise IV 20 PT a- Determine the reactions at the supports. b- Determine the force in each member of the truss c- State if the members are in tension or 3 ft compression d- If the maximum allowed in each beam is 400lb in tension and 600lb in compression, determine the maximum of admissible load P. 2 ft 2 ft Exercise V: 40 PT 1.6 kN 200 _ 400 mm + 45 The angle strut is welded to...
2. Use the Method of Joint, and determine the force in each member of the roof truss. State if the members are in tension or compression. Assume A is a pin and D is a roller support. (AB:-28.9kN; AE:14.4kN; BE:5.77kN; BC:-17.3kN; CE:-5.77KN; ED:20.2kN; CD:-40.4kN) 40 KN 20 KN 4 m D
Final Exam 2. Analyze the truss shown below: (50 Points) a. Solve for the reactions at supports A and D b. Determine the force developed in members FE, EB, and BC of the truss, and state if these members are in tension or compression. Use the method of sections, c. Draw a free body diagram (FBD) of: i. The entire truss, without its supports ii. The truss section after cutting it iii. Any joint that you solve. m 1 m...
A roof truss is loaded and supported as shown in Figure 2. The joints are all pinned. (a) Determine the support reactions at A and G. (25 marks) (b)Using "Method of joints" find the forces in members AB, AF, GF, CD and DE of the truss. State whether each of these members is in tension or compression. (75 marks) (c) Determine the force in members BC, CF and EF of the truss using "Method of sections". State whether each of...
1. A simple truss structure is given in iure I below, joint A is commected to simple pin support and Joint G is resting on roller support. Knowing that external horizontal force of 100kN acts on joint B, and vertical forces of 150KN and 50kN are acting on joint D and respectively. Determine; (a) The reaction forces at supports A and B. (3 marks) (b) Forces carmed by members AB, AD, BC, BD, CD and CE, and indicate if the...
Question Four: For the pin-jointed truss shown in Figure 4, 3m 12 KN 3m 30 kN 3m 15 kN 4m 4m 3m 3m 6m Figure 4. Calculate the reactions at A and B. (a) By inspection (involving no calculations), list all the zero force members. (b) (c) By method of joints, analyse joints T, S and N to determine the force in members ST NT, RS, SN, MN and RN. In your answer, you must state whether the members are...
engineering mechain Problem-1: (20 points) A cantilever beam is supported by a distributed load, concentrated load and moment as shown in the figure. Use wo= 1 kN/m and L=12 m. Determine the following: a. Write down the equation of shear force and bending moment for the portion of the beam from A to B. b. Draw the shear force diagram for the entire beam c. Draw the bending moment diagram for the entire beam d. What is the shear force...
or question 15 m P2 D 2 m 5: Determine the force in each member of the truss and state if the members are in tension or compression. Set P1-20 kN, P2 10 kN What is the force in member CD (kN)? What is the force in Is it in Tension or compression? CB (kN)? What is the force in member DB (KN)? Is it in Tension or compression? What s the force in member DA KN Is it in...