calculate the Maximum amount of p-aminophenol/5ml permitted in the acetaminophen 100mg/5ml. USP limit for p-aminophenol is 0.005% w/v
USP limit = 0.005% w/v = 0.005 g / 100 mL
In 5 mL, the USP limit is : 0.005 / 20 = 5 * 10-3 / 20 = 2.5 * 10-4 g / 5 mL = 0.25 mg / 5 mL
Therefore the maximum amount permitted is 0.25 mg per 5 mL
calculate the Maximum amount of p-aminophenol/5ml permitted in the acetaminophen 100mg/5ml. USP limit for p-aminophenol...
APPENDIX II: PRE-LAB ASSIGNMENT 1. Which chemical group present in acetaminophen is associated with hydrolysis Hydroxyl ii) Benzene Amide 2. 1. Which product of chemical degradation is likely to produce odor Acetic acid Carbon dioxide p-aminophenol epinephrine 3. 2. Acetaminophen is more likely to hydrolysis at Acidic pH (2-4) Alkaline pH (9-12) 4. Calculate the maximum amount of p-aminophenol/5 ml permitted in the acetaminophen 100 mg/5 ml. USP limit for p aminiphenol is 0.005% w/v
A student collects 0.165 g acetaminophen when 0.408 g of p-aminophenol reacts with 0.466 ml acetic anhydride (density= 1.08 g/mL). Calculate the limiting reactant and percent yield of the acetaminophen
9. Calculate both the maximum amount of non-P-V work and maximum amount of work per mole that can be obtained from a fuel cell that is based on the combustion of propane at 298 K. (15 pts) Substance (combustion) AH,xº (kJ/mol) San (J/K-mol) CH56 -2220 -169.6 CHx ( + 502 → __C02( + __H20 m
P = 20 kN. Calculate the following: 1. The maximum tensile and compressive stresses at the base of the mast A 2. The maximum tensile and compressive stresses at point B of the mast For each stress state at A and B indicate which side of the mast experiences tension and which side experiences compression. 0.25 m m D w 3 m H С. - 0.1 m mast cross section 3 m 60° Р B 584 mm 6 m mast...
By assuming P and L calculate the moment of inertia (I1,I2, and I3) and the maximum bending stress as it mentioned below THEORETICAL CALCULATION Support Reactions. If P= N and the L. is _mm: a free body diagram of entire beam is shown in Fig. 2 (a) +F;=0; -P+A,+C, =0 L/2 +M = 0; - P(1/2)+C,L=0 L/2 YU L C Region AB AO Shear and Moment Functions. A frec-body diagram of the left segment of the beam is shown in...
Calculate the maximum amount of work that can be obtained at 25°C from an electrochemical cell using Cd and PbO2 electrodes. HINT: Write a balanced chemical reaction first. Reduction Half Reaction Standard Reduction Potential (E"[v] PbO2(s) + 4H(aq) + 2e-Pb2+ (aq) + 2H2010 1.46 V Ca2+ (aq) + 2e + Ca(s) -0.40 V 179) 205 k) 0 102 kJ 0 359K 673 kJ
1.) What is the fill factor of a solar cell having maximum power P(max) = 1.5 W? The open circuit voltage and short circuit current of the cell are V(oc) = .6 V and J(sc) = 2.8 A, respectively. 2.) A solar cell with dimensions 12 cm x 12 cm is illuminated at standard test conditions. The cell has the following external parameters: V(oc) = .8 V, I(sc) = 3 A, V(MPP) = .75 V, I(MPP) = 2.5 A. Calculate...
7. a) A Si p-n junction has dopant concentrations Na = 2 x 1016/cm3 and Nd=1x1015/cm3 at T=300 K. Calculate (a) Vo, (b) W at VR=0 and VR=2 V and (c) the maximum electric field in the space charge region at VR=0 and VR=4 V. b) For the junction in part a, how much would the temperature need to increase to have V0 decrease by 1%?
Plz do number 2 EENG-270 Note: Close Book. Calculators allowed. 145 points maximum p+1 -100. Calculate up to 3 significant figures at every step. Show all steps. Assume V, 25mV, v . νο" Vs' 0.TV an v first before using numerical values. For all numerical answers, show a general expression f For the diode circuit shown: (a)Draw the single loop DC equivalent circuit ( after Thevenin simplification). (15 pts.) (b) Find the quiescent diode current lo and VOUTDC: saturated. (15...