the first question answer is 4
volts .option d is the right one .but in 2 nd question there is no
correct answer 4 ma is correct answer.
(TCO 5) If Va 1V, what is Vout? 1 k 2 k Va Ia 2 k Vout 0 -4 V ov
TCO 2) For the circuit below, if Vcc is 28 volts and Rb is 4.7k ohms, find the base and collector voltages and currents for an input of OV and 5V. Beta 300, the motor resistance is 400 ohms. AG1 NI MOTOR SERVO Vin N Yout Rb 1a: When Vin OV, find: lb = Ic = Vbase Vcol 1b: when Vin 5V, find: IC Vbase HTML Editor Question 6 7 pts TCO 1) Find the following for an input of...
7 pts Question 5 (TCO 2) For the circuit below, if Vcc is 20 volts and Rb is 4.3k ohms, find the base and collector 300, the motor resistance is 100 ohms. voltages and currents for an input of OV and 5V. Beta Vcc ant Vin -n Vout Rb 1a: Whan Vin- OV. find: ть Ic = Vhase 1b: When Vin 5V. find: Ib Ic = vbase Vcol HINIL Edilotia A TE U A- B I Paragraph T 12p ED...
Problem 10: Consider the differential stage biased by current mirror and loaded with capacitor. MOSFET parametes: Vr-1 V; VA-; (W/L)*kn-2 mA/V; negligible internal capacitances. 5V 8k 10k 5n Vout 5V Find 1. 2. 3. DC voltage at the output; Low frequency small signal voltage gain Vout/Vin; High frequency 3 dB cutoff.
Problem 10: Consider the differential stage biased by current mirror and loaded with capacitor. MOSFET parametes: Vr-1 V; VA-; (W/L)*kn-2 mA/V; negligible internal capacitances. 5V 8k 10k 5n Vout...
Vin - 5V, nom (15.02V) Vout = 15V, nom R9 > 10K nok <Pload Boost Switching Regulator Ventri I=0 --> (45.1 ohms) (2.058V) 2.3 R10 5K Vin 5v, nom ZR7 2.2k (5.14V) ET < R1 2.7k (2.947V) Vin = 5V, nom R8 1.2k (2.061V) I=0 UJA TLC272 Da, Db, D3c I=0 --> 1N914 3 diodes in series! 70 D2 (2.421V) ID2? --> 1N914 on the diagram. Using DC measured values, to ground, are shown in these measured values, determine: 1....
2. For the circuit below, given that Vin 3V, R 30 K2, and R2 20 KQ, in Vout Ri A. What is the voltage at the negative () input of the op amp? B. What is Vout? C. What will the current be through R2 (from Vout to the negative input of the op amp)? Last printed 3/12/18 2:56:00 PM BioE 1310, Spring 2018 Page 2 of 2 D. What will the current be through Ri (from the negative input...
For the diodes, use the models shown below; the regular diode
model has 0.7V forward bias voltage; the Zener diode model has -3V
breakdown voltage
Question 2 (25 points) For the diodes, use the models shown below; the regular diode model has 0.7V forward bias voltage; the Zener diode model has -3V breakdown voltage. a) Determine the minimum positive value of in to make D1 conduct current. (10 pts) b) Determine the minimum positive value of lin to make D2...
2. Sketch Vout VS Vin and Vout if Vin-10sin(2TT60t) for each of the following circuits. You may assume that the forward diode drops for the diodes equals zero Vout s v out Vin 5 V Vout out 3. Repeat problem 2 but with forward diode drops equal to 0.7 V 4. What are the primary mechanisms for current flow in a. A forward biased diode. b. A reverse biased diode not in breakdown. c. A reverse biased diode in breakdown...
Objective After performing this experiment, you will be able to 1. Measure Vout, Av 2. Verify the operation of CE Amplifier PART 1 (MULTISIM SIMULATION) 1. Wire up the following circuit on Multisim and fill the following table: Consider: Vin 20mVp-p F 1KHz VCc +10 V BDC= 150 Ba= 175 RC 4.7 k C3 V out 47 k2 C 10 μF 10 μF 47 k R 560 ! Re 470 10 k 100 μΕ 470 Av Vout/Vin Vout As is...
Part 1: Gain =8, R1=5k, R2=20k, R5=100, and V1=1V. Find
Vout/Vin.
Part 2: Let R4=0 and R3=∞. Find Vout/Vin. (Hint: make sure the
button called Enable Biased Voltage
Display is depressed) (Another Hint: when a resistance is zero,
short it; when a resistance is
infinity, delete it).
Part 3: Let R4=2k and R3=∞. Find Vout/Vin.
Part 4: Let R4=0 and R3=1000. Find Vout/Vin.
Part 5:Let R4=2k and R3=1000. Find Vout/Vin.
R1 Vout G1 5k R4 1k R5 100 V1 R2...