Thegas turbine cycle shown below is used as an automotive engine. Inthe first turbine, the gas expands to pressure P5, just low enough for this turbine todrive the compressor. The gas is then
expanded through thesecond turbine to drive the wheels. Data for the engine are shownon the figure. Assume all processes are ideal. Determine theintermediate pressure P5, the net specific work output from the engine, and the massflow rate through the engine. Also find the air temperatureentering the burner T3 and the thermal efficiency of the engine. (0.339kg/s)
Thegas turbine cycle shown below is used as an automotive engine. Inthe first turbine, the gas...
1. A combined gas-steam power cycle uses a single gas turbine cycle for the air cycle and a simple Rankine cycle for the water vapor cycle. Atmospheric air enters the compressor at a rate of 88.2 lbm / s, at 14.7 psia and 59 ° F, and the maximum gas cycle temperature is 1,742 ° F. The pressure ratio in the compressor is 7. The isentropic efficiency of both the compressor and the turbine is 80%. Gas exits the heat...
Problem 1 (15 pts) A gas turbine cycle operates with a compressor pressure ratio of 12 and a mass flow rate of 5.0 kg/s. Air enters the compressor at 1 bar, 290 K. The maximum cycle temperature is 1600 K. For the compressor, the isentropic efficiency is 85%, and for the turbine the isentropic efficiency is 90%. Using an air-standard analysis with air as ideal gas with constant specific heats, calculate: a) the volumetric flow rate of air entering the...
Problem 2/2 (50%) -The gas-turbine cycle of a combined gas-steam power plant has a pressure ratio of 12. Air enters the compressor at 310 K and the turbine at 1400 K. The combustion gases leaving the gas turbine are used to heat the steam at 12.5 MPa to 500 C in a heat exchanger. The combustion gases leave the heat exchanger at 247"C. Steam expands in a high pressure turbine to a pressure of 2.5 MPa and is reheated in...
The gas turbine cycle of a gas-steam combined cycle power plant has a pressure ratio of 12. The air enters the compressor at 310 K and 100 kPa (1) and the turbine at 1400 K (3). The combustion gases leaving the gas turbine (4) are used to heat the steam to 12.5 MPa up to 500 °C (6) in a heat exchanger. The flue gas exits the heat exchanger (5) at 247 °C. The steam is expanded in a high...
Energy Convertion hello, please help me quickly please please thank you Question B (15 marks) You are to analyze a combined cycle that consists of a gas (air) turbine cycle (top) ttom). The gas cycle has the following operating conditions: inlet pressure to compressor one bar inlet temperature-300 K operating pressure ratio-12 Maxmum allowable temperature 1150 °C adiabatic efficiency for compressor 0.83 adiabatic efficiency for turbine-0.87 - - The exhaust leaves stack at 120 °C after vaporizing water in the...
Consider the combined gas-steam power cycle,The topping cycle is a gas-turbine cycle that has a pressure ratio of 8.Air enters the compressor at 300K and the turbine at 1300K.The isentropic efficiency of the compressor is 80 percent, and that of the gas is 85 percent.The bottoming cycle is a simple ideal Rankine cycle operating between the pressures limits of 7 MPa and 5 KPa.Steam is heated in a heat exchanger by the exahust gases to a temperature of 5000C.The exhaust...
2. Consider a combined gas steam power cycle. The gas cycle is a simple Brayton cycle that has a pressure ratio of 7. Air enters at 9.8 kg / s at the compressor at 15 ° C and 100 kPa, and at the gas turbine at 950 ° C. The steam cycle is a Rankine cycle with overheating between the pressure limits of 6 MPa and 10 kPa. The water vapor is heated in the heat exchanger at a rate...
Question A.1 A schematic of a gas turbine combined cycle generating plant is shown in Figure A1.1 on the next page. Exhaust gas from the gas turbine generator pass througha heat recovery steam generator (HRSG) which generates steam to drive a steam turbine generator. The following data is provided for the plant: Gas turbine 18.9:1 Pressure ratio Compressor air inlet temperature Turbine inlet temperature 15°C t 273 288 1350°C +273- 1623 588 kg/s T, T3 Exhaust gas mass flow Isentropic...
4. A regenerative two-stage gas turbine with reheat operating on the standard-air Brayton cycle is illustrated in Figure 3. In an ideal Brayton cycle, the processes in the turbines and compressor are adiabatic and isentropic, and the air flows through the combustor and heat exchangers at constant pressure. a) Show that the maximum total work output is developed when the pressure ratio is the same across each stage, if the temperature at the inlet to each turbine stage is the...
Problem4 (a) (40 points) A combined gas-steam powe cycles. The ideal Brayton and Rankine plant operates on Rankine cycle has a reheater. The Brayton cycle operates on a gas- of the gas-turbine cycle 1400 K The 15MPa to ercooling, reheating, and regeneration cycle. The pressure ratio 300 K for compressor stages is do Air enters compressors a combustion gases leaving the lower pressure gas turbine are used to heat the steam at C in a heat exchanger. The combustion gases...