Plz give a thumbs up
Each of the four vertical links has an 8 × 36-mm uniform rectangular cross section and...
Each of the four vertical links has an 8 × 36-mm uniform rectangular cross section, and each of the four pins has a 16-mm diameter. Take P= 24 kN 0.4m 025 m 0.2 m
Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section, and each of the four pins has a 16-mm diameter. Take P=23 kN. 0.2 m Determine the maximum value of the average normal stress in the links connecting points B and D.
Each of the four vertical links has an 8x36-mm uniform rectanqular cross section and esch of the four pins has a 16-mm diameter. Take P 19 kN 04 m 025 (02 m Requie Determine the average bearing stress at B in member ABC, knowing that this member has a 10 x 50-mm uniform rectangular cross section (Round the final answer to one decimal The average bearing stress at B in member ABC is MPa Each of the four vertical links...
Esch of the four vertical iniks hes an 8-36-mm unform rectangular cross section, and each of the four pins has a 16-mm diameter Take P 22 kN 2m References Section Brealk Dfficuty Medium 12. 100 O You did not full credit for 000 points Determine the maxmum value of the The maximum value of the average nomal stress in the inks connecting points C and Es average normal stness in the inks connecting points c and E Round the nal...
A rigid member ABC is subjected to a 20 kN vertical force and is attached to a base by four vertical bars and four pins as shown below. All vertical bars are identical with rectangular cross sections (80 mm x 20 mm), and each of the four pins has a 24-mm diameter. Determine the maximum value of the average normal stress in each of the vertical bars 0.4 m C 0.25 m 0.2 m 20 kN A A rigid member...
* You received no credit for this question in the previous attempt Check my work Part 1 of 2 Required information Each of the four vertical links has an 8 x 36 mm uniform rectangular cross section, and each of the four pins has a 16-mm diameter. Take P= 23 kN. points Determine the maximum value of the average normal stress in the links connecting points and D The maximum value of the average normal stress in the links connecting...
Column ABC which is supported by pins at both ends has a uniform rectangular cross section and is braced in the xz plane at its midpoint C so as to avoid translation only. A. Determine the ratio b/d for which the factor of safety is the same with respect to buckling in the xz and yz planes. B. Using the ratio found in part a, design the cross section of the column so that the factor of safety will be...
A rectangular beam is subjected to the loadings shown in Figure Q.16(a) has cross section of 100 mm x 300 mm as shown in Figure Q.16(b). An axial load of 5 kN is applied along the centroid of the cross-section at one end of the beam. Compute the normal stress and shear stress at point P through the cut-section of P in the beam. [15 marks] у 10 kN/m P Ž 5 KN --- 00 P k 3 m -...
The shown frame ABC has beam AB with a rectangular cross section of 150 mm by 200 mm. Attached rod CB has a cross sectional area of 1250 mm2 and is pin-connected to beam AB at B. Use the Stiffness Method to Find the force in BC and the reactions at A a) Use the Stiffness Method to find the force in BC and the reactions at A If the horizontal displacement at B0.01688 mm, the vertical displacement at B...
1.52 Solve Prob. 1.51, assuming that the structure has been redesigned to use 16-in.-diameter pins at A and C as well as at B and that no other changes have been made. A in. 8 in. B C 4 in. 6 in. Fig.P1.51 1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 2-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter...