Please rate the answer. Thank you.
what is the stress for the aluminum and steel if the diameter is 6mm and for...
The following table shows the maximum amount of steel or aluminum that Canada and France can produce if all factors of production are fully employed. Assume that production occurs under constant-cost conditions. In the absence of trade, Canada produces and consumes 600 tons of aluminum and 300 tons of steel, and France produces and consumes 400 tons of aluminum and 600 tons of steel. Canada France Steel (tons) 500 1,200 Aluminum (tons) 1,500 800 On the following graph, draw the...
Identify the material. that fits the stress-strain curve. A) MILD STEEL Yield Strength: 30 kN, Ultimate Strength: 40 kN, Young Modulus: 30/0.7 kN/mm = 43 kN/mm B) ALUMINUM Yield Strength: 20 kN, Ultimate Strength: 26 kN, Young Modulus: 20 kN/mm C) CAST IRON Yield Strength: N/A, Ultimate Strength: 20 kN, Young Modulus: 20/0.4 kN/mm = 50 kN/mm D) COPPER Yield Strength: 30 kN, Ultimate Strength: 35 kN, Young Modulus: 30 kN/mm Instructions CLI Tesile TesTeR Test Specimens Material - Mild...
17) Figure 9-12 (1pts) Price 84 Domestic Supply 78 72+ 66 60 World Price 54 48 42 36 30 24+ 18 + 12 Domestic Demand 6 Quantity 2000 2400 2800 1600 1200 800 400 NO Refer to Figure 9-12. Producer surplus after trade is $28,000. $30,000 $35,200. $38,400. 11 12 13 14 | 15 | 16 17 18 19 1 20 Previous
It is desired to evaluate the tensile properties of an aluminum alloy. A tensile test is performed using a standard cylindrical tensile specimen with a diameter of 12.8 mm and a gauge length of 50.800 mm. The gage length and final diameter of the sample are measured after the sample is removed from the testing machine. The gage length and the diameter of the necked region after the specimen was removed from the testing machine are 60 mm and 9...
Suppose there are 100 identical firms in the market and the luggage industry is perfectly competitive. What does the market supply curve look like? 20 19 18 17 16 15 14 13 12 11 A 10 20 19 18 17 16 15 14 13 12 11 A 10 8 7 5 2 1 0 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 4 5 6 7 8 9 10 11 12 0 1...
2) Using the stress-strain curve for a steel alloy shown in the following figure answer the following questions: 600 500 400 500 400 300 300 200 200 100 100 0.000 0.002 0.006 0.004 Strain 0.00 0,04 0.08 0.12 0.16 0.20 Using the same steel alloy, consider a cylindrical specimen 15 mm in diameter pulled in tension, if a load of 85,000 N is applied: h) Calculate the approximate ductility in percent elongation, (consider the final elongation as the elongation at...
Suppose there are 100 identical firms in the market and the luggage industry is perfectly competitive. What does the market supply curve look like? 20 19 18 17 16 15 14 13 12 11 A 10 9 8 7 6 5 4 20 19 18 17 16 15 14 13 12 11 A 10 8 7 6 2 1 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 0 1 2 3 4 5...
1. Draw a schematic stress-strain diagram for steel. Make sure you mark all the important points and regions on it. Provide a one-two sentence explanation for each point and region along the diagram. 2. A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa (30 x 10* psi) and an original diameter of 10.2 mm (0.40 In.) will experience only elastic deformation when a tensile load of 8900 N (2000 Ibe) is applied. Compute the maximum length...
Analyze the FTIR Spectrum for the following FTIR Spectrum for starting material: 2-chloro-2-methyl-propane BP: FTIR Common Name: IUPAC Name: MP: MICRONS 2,2 2,3 24 25 26 27 28 29 3 3,5 4 45 5 5,5 7 8 9 10 11 12 13 100 14_15 16 17 18 19 21 22 200 7 05 90 % 80 7 10.1 T 70 A N 80 0.28 50 03 40 -0.44 N30 c E 20 -0.5 0.6 -07 E08 F1.0 10 4500 4400...
(GPa) A cylindrical machine part 250 mm long with a diameter of 10 mm is subjected to an axial load of 28,500 N. Using the list of materials shown in the table below, answer questions 1 through 2. Yield Strength Young's Modulus Material [MPa] Density (g/cm] Aluminum alloy 255 70 2.75 Steel alloy 400 207 7.85 Titanium alloy 800 110 4.50 Copper alloy 250 110 8.50 Brass alloy 340 100 8.40 1. If the elongation is not to exceed 0.6...