A circular hoop of mass m, radius r, and infinitesimal thickness rolls without slipping down a ramp inclined at an angle θ with the horizontal. (Intro 1figure)
part a)
What is the acceleration of the center of the hoop?
Express the acceleration in terms of physical constants and all or some of the quantities m,r,and θ.
part b)
What is the minimum coefficient of (static)friction needed for the hoop to roll without slipping? Note that it is static and not kinetic friction that is relevant here, since the bottom point on the wheel is not moving relative to the ground(this is the meaning of no slipping).
Express the minimum coefficient of friction in terms of all or some of the given quantities m,r,and θ.
The concepts used in this question are rotational motion, torque, and static friction.
Firstly, draw a free-body diagram of the forces acting on the circular hoop and use the torque expression to find the equation of motion of the circular hoop.
Finally, balance the forces along the vertical axis and find the coefficient of static friction.
The torque due to a force is as follows:
Here, f is the force which causes the torque and r is the radial distance from the axis of rotation to the line of force.
The expression of torque can be written as follows:
Here, I is the moment of inertia of the system and is the angular acceleration of the system.
The angular acceleration is given by the following expression:
Here, a is the tangential acceleration and r is the radius.
The force of static friction is given by the following expression:
Here, N is the normal force and is the coefficient of static friction.
(a)
The figure 1 shows a free-body diagram of a circular hoop rolling down an inclined plane. The weight mg is acting in downward direction and its components are resolved along the x and y axes. A force of friction f is acting along the negative x-axis.
Balance all the forces along the x-axis and rearrange the expression for f.
The torque is acting on the hoop due to the friction force. The torque due to friction force is given as follows:
The angle between the direction of friction and r is 90 degrees. Substitute 90o for in the above expression.
The torque generates an angular acceleration in the circular hoop. The expression of torque can be written as follows:
Substitute rf for in the above expression.
The angular acceleration is given by the following expression:
Substitute for and for f in the equation and solve for a.
The moment of inertia of a circular hoop is as follows:
Substitute for I in the expression .
(b)
Refer figure 1, balance all the forces acting along y-axis.
The force of friction in calculated in part a is as follows:
Substitute for and for I in the above expression.
The force of static friction is given by the following expression:
Substitute ma for f and for N in the above expression.
Substitute for a in the above expression.
Ans: Part a
The acceleration is
A circular hoop of mass m, radius r, and infinitesimal thickness rolls without slipping down a ramp inclined at an angle θ with the horizontal. (Intro 1figure)
A very thin circular hoop of mass(m) and radius(r) rolls without slipping down a ramp inclined at an angle(theta) with the horizontal, as shown in the figure.What is the acceleration(a) of the center of the hoop? Express your answer in terms of some or all of the variablesm,r, theta, and the magnitude of the acceleration due to gravity(g).
1) A solid ball of mass M and radius R rolls without slipping down a hill with slope tan θ. (That is θ is the angle of the hill relative to the horizontal direction.) What is the static frictional force acting on it? It is possible to solve this question in a fairly simple way using two ingredients: a) As derived in the worksheet when an object of moment of inertia I, mass M and radius R starts at rest...
A hoop of mass M = 2 kg and radius R = 0.4 m rolls without slipping down a hill, as shown in the figure. The lack of slipping means that when the center of mass of the hoop has speed v, the tangential speed of the hoop relative to the center of mass is also equal to VCM, since in that case the instantaneous speed is zero for the part of the hoop that is in contact with the...
A solid sphere of uniform density starts from rest and rolls without slipping down an inclined plane with angle θ = 30o. The sphere has mass M = 8 kg and radius R = 0.19 m . The coefficient of static friction between the sphere and the plane is μ = 0.64. What is the magnitude of the frictional force on the sphere? Ff = N
Bowling Ball. A bowling ball rolls without slipping up a ramp that slopes upward at an angle to the horizontal. Treat the ball as a uniform solid sphere of mass M and radius R, ignoring the finger holes. a) Draw the free-body diagram for the ball. Explain why the friction force must be directed up the ramp. b )What is the acceleration of the center of mass of the ball? c) What minimum coefficient of static friction is needed to...
A uniform drum of radius R and mass M rolls without slipping down a plane inclined at angle . Find its acceleration along the plane (translational acceleration). The moment of inertia of the drum about its axis through the center is I = MR^2/2 .
A hoop with mass, M, and radius, R, rolls along a level surface without slipping with a linear speed, v. What is the ratio of rotational to linear kinetic energy? (For a hoop, I = MR2.)
Scenario A thin hoop of mass M and radius R is released from rest at the top of a ramp of length L as shown at right. The ramp makes an angle with respect to a horizontal tabletop to which the ramp is fixed. The table top is height H above the floor. Assume that the hoop rolls without slipping down the ramp and across the table. Express all algebraic answers in terms of given quantities and fundamental constants. PARTC:...
A hoop of mass M = 3 kg and radius R = 0.4 m rolls without slipping down a hill, as shown in the figure. The lack of slipping means that when the center of mass of the hoop has speed v, the tangential speed of the hoop relative to the center of mass is also equal to vCM, since in that case the instantaneous speed is zero for the part of the hoop that is in contact with the...
A thin, circular hoop of mass m and radius R rolls down a parabolic path POR from height without slipping (assume R*) as shown in the figure below. Path PQ is rough (and so the shell will roll on that path), whereas path QR is smooth, or frictionless (so the shell will only slide, not roll, In this region). Determine the heighth above point reached by the shell on path QR. (Use the following as necessary m, 9. Hand R.)...