At what temperature will the bolts touch? The initial
temperature of the system is 27 degrees Celsius. Assume the support
walls do not move. Answer = 34 degrees Celsius
At what temperature will the bolts touch? The initial temperature of the system is 27 degrees...
2. An electronic device has been poorly designed so that two bolts attached to different parts of the device almost touch each other in its interior. The steel and brass bolts are at different electric potentials and if they touch,0tid0 0 a short circuit will develop managing the device. If the initial gap between the end of the bolts is 5x106 m at 25°C, at what temperature will the bolts touch? (abrass 198 106 oC" ; αsteel I 1 x...
An isolated gas (nitrogen, N2), at initial temperature of 22.7 degrees Celsius, is expanded from as initial volume of 0.750L to 1.450L at constant pressure, P=132kPa. During this process the gas absorbs 318.5J of heat. i. Calculate the work output by the system during this expansion ii. Estimate the specific heat capacity of the gas for this process. Express your answer in J/kg*K.
Part A A sample of gas in a balloon has an initial temperature of 27 °C and a volume of 1830 L. If the temperature changes to 76 °C, and there is no change of pressure or amount of gas, what is the new volume. V. of the gas? Express your answer with the appropriate units. View Available Hint(s) of 1 Value Units Submit Part B What Celsius temperature. Ty, is required to change the volume of the gas sample...
#1883. show steps and equations used. Answer in the back of
the book is 70 degrees celcius.
tension), when the whole system is at 0 °C. What is the tensile stress in the steel wires when the temperature of the system is raised to 300 °C? Make any simplifying assumptions you think are justified, but state what they are. BRASS 1881 A steel bomb is filled with water at 10 °C. If the entire bomb is heated to 75 °C...
In this problem you will estimate the heat lost by a typical house, assuming that the temperature inside is T(in) = 20 degrees celcius and the temperature outside is T(out) = 0 degrees celcius. The walls have fiberglass insulation, which dominates the heat conduction properties of the wall So we can consider the wall to have a thermal conductivity of k(wall) = 0.048 W/m/K . We will take the thickness of the walls and ceiling to be L(wall) = 12...
Given that the initial rate constant is 0.0180s−1 at an initial temperature of 30 ∘C , what would the rate constant be at a temperature of 180. ∘C for the same reaction described in Part A? Express your answer with the appropriate units. (I solved this and got 2.01, which is wrong, but I'm not exactly sure why). (Reaction A was: The activation energy of a certain reaction is 44.3 kJ/mol . At 30 ∘C , the rate constant is...
A family going fishing puts 1.5 kg of ice in a cooler. The initial temperature of the ice is -4.0 ∘C. When 2.7×105 J of heat has leaked into the cooler, what is the temperature now? Express your answer using one significant figure. T = ? degrees celsius Is there any ice left? If not zero, how much? Express your answser using one significant figure. m(ice) = ? kg
A gas has a volume of 4.10 L at 0 ∘C. What final temperature, in degrees Celsius, is needed to change the volume of the gas to each of the following, if n and P do not change? 1.00 L Express your answer using three significant figures. 1800 mL Express your answer using two significant figures 10.5 L Express your answer using three significant figures. 54.0 mL Express your answer using three significant figures.
A gas system has an initial volume of 820 mL with the temperature unknown. When the volume changes to 7080 mL the temperature is found to be 2460 K. What was the initial temperature in K? Use three significant figures in your answer and do not enter units... numbers only!
QUESTION 1 A gas system has an initial volume of 12400 mL with the temperature unknown. When the volume changes to 1200 ml the temperature is found to be -241.6 °C. What was the initial temperature in K? Use three significant figures in your answer and do not enter units... numbers only!