Problem 4. (15 pts) The cylindrical pressure vessel is made of an aluminum alloy [E 7°...
The cylindrical pressure vessel shown in the figure has an inside diameter of 980 mm and a wall thickness of 12 mm. The cylinder is made of an aluminum alloy that has an elastic modulus of E = 72 GPa and a shear modulus of G = 27.5 GPa. Two strain gages are mounted on the exterior surface of the cylinder at right angles to each other. The angle θ is 21°. If the pressure in the vessel is 1.86...
Question 1 The cylindrical pressure vessel shown has an inside diameter of 625 mm and a wall thickness of 5 mm. The cylinder is made of an aluminum alloy that has an elastic modulus of E = 70 GPa and a shear modulus of G-26.3 GPa. Two strain gages are mounted on the exterior surface of the cylinder at right angles to each other; however, the angle θ is not known. If the strains measured by the two gages are...
Question 2 The cylindrical pressure veese shown in the figure has an inside diameter of 910 mm and a al thickness of 10 mm. The cylinder is made of an aluminum alloy that has an elastic modulus of E = 70 GPa and a shear modulus of G = 27.0 GPa mounted on the exterior surface of the cylinder at right angles to each other. The angle θ is 28°. If the pressure in the vessel is 1.69 MPa. determine:...
0.10m Assuming the surface of an Aluminum (E-70 Gpa and v = 0.30) cylindrical pressure vessel is in a state of plain stress, with an internal gas pressure of P - 8 MPa. Determine the strain in the z-direction (z) if the "hoop" stress and "longitudinal" stress of the vessel are defined as: OLA P-r Pr and ơL--2t if the radius of the pressure vessel is r-0.04 m and the wall thickness is t 0.004 mm. Note: the image to...
13. (a) The cylindrical walls of a vessel of outer radius R and wall thickness (t <<R) are made of an isotropic linear elastic material with modulus E and Poisson's ratio v. The end caps are rigid. If the vessel is empty (zero gage pressure), the vessel fits precisely (without any stress) inside a rigid frictionless well. A pressurized fuel is introduced in the vessel so that the internal gage pressure in the vessel is now P. For these conditions...
A strain gauge affixed to the outside of a cylindrical pressure vessel at an angle of θ = 35° reads ε = 400 μm/m. The outside diameter of the vessel is 500mm and the wall thickness is 5 mm. If the veseel is constructed of A36 steel, determine the following: a) The hoop and longitudinal stresses in the tank. Hints: To solve you will need to consider the equations for strain transform and generalized Hooke’s Law. The hoop and longitudinal...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint α 55° with the longitudinal axis. The vessel has inner radius r-1.8 m and wall thickness t 20 mm. The material is steel with modulus E: 200 GPa and Poisson's ratio0.30. The internal pressure p is 800 kPa Helical weld . The helical weld makes...
please give me a detailed explanation for part C. please only answer if you can help.will rate good answer. 1. A long, mild steel cylindrical pressure vessel with diameter 2 m has an operating pressure of 30 bar and a wall thickness of 30 mm. (a) Calculate the hoop and longitudinal stresses in the cylindrical wall. 13 marks] (b) Determine the safety factor using Tresca's yield criterion 2 marks] (c) A 45° strain gauge rosette is attached to the curved...
em 35? ? A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint. The helical weld makes an angle ? 350 with the axial direction. The vessel has inner radius r = 1.8 m and wall thickness 20 mm. The material is steel with E 200 GPa and Poisson ratio 0.3. The internal pressure p = 800...
Question 1 An end capped cylindrical pressure vessel with internal pressure p = fully supported at one end, is also subjected to a force F= 10 kN in the y direction at the other end as shown. The internal diameter of the pressure vessel is d= 160 mm and its thickness is t= 10 mm 3 MPa, assumed to be Determine the magnitudes of the stress components in x, y and z coordinates at points H and K and sketch...