PRACTICE IT Use the worked example above to help you solve this problem. In a car...
LEARN MORE REMARKS In this problem, we didn't address the effect of possible differences in the helghts of the pistons. If the column of fluid is higher in the small piston, the fluid weight assists in supporting the car, reducing the necessary applied force. If the column of fluid is higher in the large piston, both the car and the extra fluid must be supported, so additional applied force is required. QUESTION if the radius of the output piston is...
004 (part 1 of 2) 10.0 points In a car lift used in a service station, com- pressed air exerts a force on a small piston of circular cross-section having a radius of 4.56 cm. This pressure is transmitted by a liquid to a second piston of radius 26.7 cm. What force must the compressed air exert in order to lift a car weighing 11600 N? Answer in units of N. 005 (part 2 of 2) 10.0 points What air...
A hydraulic car lift has an input piston of radius 2.00 cm and negligible weight. The output piston has a radius of 79.2 cm, and the total load on the output plungers is 18000 N. If the car (output piston) needs to be lifted 1.70 m, what volume of non-compressible hydraulic fluid must be pumped into the system?
A 14,192-N car is raised using a hydraulic lift, which consists of a U-tube with arms of unequal areas, filled with incompressible oll with a density of 900 kg/m3 and capped at both ends with tight-fitting pistons. The wider arm of the U-tube has a radius of 19.3 cm and the narrower arm has a radius of 3 cm. The car rests on the piston on the wider arm of the U-tube. The pistons are initially at the same level....
Need ASAP To inspect a 20, 500 N car, it is raised with a hydraulic lift, if the radius of the small piston is 5.0 cm, and the radius of the large it is position is 10 cm, find the force that must be exerted on the small piston to lift the car.
A 10,000-N car is raised using a hydraulic lift, which consists of a U-tube with arms of unequal areas, filled with oil and capped at both ends with tight-fitting pistons. The wider arm of the U-tube has a radius of 18.0 cm and the narrower arm has a radius of 5.00 cm. The car rests on the piston on the wider arm of the U-tube. The pistons are initially at the same level. What is the initial force that must...
A 14 500-N car on a hydraulic lift rests on a cylinder with a piston of radius 0.100 m. If a connecting cylinder with a piston of 0.050-m radius is driven by compressed air, what force must be applied to this smaller piston in order to lift the car? A. 3.53E+3 N B. 5.80E+1 N C. 4.13E+3 N D. 1.45E+4 N E. 3.63E+3 N
A car on a hydraulic lift rests on a cylinder with a piston with a diameter of 30 cm. If a connecting cylinder is driven by compressed air with a pressure of 65 psi, how big the force approximately will be generated to the piston to lift the car? a. 3,000 lb. b. 4,500 lb. c. 6,000 lb. d. 8,000 lb e. 12,000 lb
The answer is E A 12,000-N car is raised using a hydraulic lift, which consists of a U-tube with arms of unequal areas, filled with oil with a density of 800 kg/m^3 and capped at both ends with tight-fitting pistons. The wider arm of the U-tube has a radius of 18.0 cm and the narrower arm has a radius of 5.00 cm. The car rests on the piston on the wider arm of the U-tube. The pistons are initially at...
To work on your car you use a hydraulic lift as shown in the diagram. It confines a fluid with ρ = 2.16 kg/m3.Your car has mass Mcar = 980 kg. The lift piston has mass Mpiston = 225 kg. The input piston (on the left) is massless and has an area of 0.785 m2. The lift piston (on the right) has an area of 4.14 m2. 1. The lift piston base and the input piston base are at the...