2. A steel bar 20.00 cm long is welded end to end with a brass bar...

Question

Question

Answer 1

Answer #1

5-2. 5633 e 0 26 W

please rate it up thanks :)

Answer 2

Similar Homework Help Questions

A) A stainless steel bar 11.8 cm long is welded end to end to a copper...

A) A stainless steel bar 11.8 cm long is welded end to end to a copper bar 22.6 cm long. Each bar has a square cross section, 2.0 cm on a side. The free end of the stainless steel bar is kept at 100∘C by placing it in contact with steam, and the free end of the copper bar is kept at with 0∘C by placing it in contact with ice. Both bars are perfectly insulated on their sides. What...
Two rods, one made of brass and the other made of copper, are joined end to...

Two rods, one made of brass and the other made of copper, are joined end to end. The length of the brass section is 0.160 m and the length of the copper section is 0.640 m. Each segment has cross-sectional area 0.00680 m². The free end of the brass segment is in boiling water and the free end of the copper segment is in an ice and water mixture, in both cases under normal atmospheric pressure. The sides of the...
Exercise 17.56 Two rods, one made of brass and the other made of copper, are joined...

Exercise 17.56 Two rods, one made of brass and the other made of copper, are joined end to end. The length of the brass section is 0.200 m and the length of the copper section is 0.800 m. Each segment has cross-sectional area 0.00700 m2 The free end of the brass segment is in boiling water and the free end of the copper segment is in an ice-water mixture, in both cases under normal atmospheric pressure. The sides of the...

Heat Flowing through a Sectioned Rod

A long rod, insulated to prevent heat loss along its sides, is in perfect thermal contact with boiling water (at atmospheric pressure) at one end and with an ice-water mixture at the other. The rod consists of a 1.00 m section of copper (with one end in the boiling water) joined end-to-end to a length L2 of steel (with one end in the ice water). Both sections of the rod have cross-sectional areas of 4.00 cm2. The temperature of the copper-steel junction...
A long steel bar of radius R=2.5 cm, k =50 W/(m °C), p= 7800 kg/m), and...

A long steel bar of radius R=2.5 cm, k =50 W/(m °C), p= 7800 kg/m), and c = 0.5 kJ/(kg. . °C) is to be annealed by cooling slowly from 800.°C to 100.°C in an environment at temperature 50.°C. If the heat transfer coefficient between the environment and the surface of the bars is h = 45 W/(m .°C), determine the time required for the annealing process using lumped system analysis.
A long steel bar with a diameter of 4 cm (ρ = 7840 kg / m3...

A long steel bar with a diameter of 4 cm (ρ = 7840 kg / m3 , cp = 580 J / kg ° K, k = 52 W / mK, α = 1.21x10-5 m2 / s), internal enters the 2 m long moving belt heat treatment furnace at ambient temperature of 900 ° C at 40 ° C. Since the film coefficient in the oven is 100 W / m2K, the center axis temperature of the bar at the...

4. A long square steel bar 2L - 7 cm wide by 21 - 7 cm...

4. A long square steel bar 2L - 7 cm wide by 21 - 7 cm high having a thermal conductivity k, = 14 W/n'c and a thermal diffusivity a 3.63x10 m/s is hot rolled at T. - 615°C and then cooled by air issuing from jets at T. -30°c. After t - 287 s have elapsed, the temperature at the center of the bar T(0,0,t) - 240c and the temperature at the corners of the bar T(L,Lt) - 125c....
One end of a long rod 3 cm in diameter is inserted into a furnace with the

One end of a long rod 3 cm in diameter is inserted into a furnace with the (3 outer end projecting into the outside air. Once the steady state is reached the temperature of the rod is measured at two points, 15 cm apart and found to be 140°C and 100°C, when the atmospheric air is at 30°C with convection coefficient of 20 W/m2.K. Calculate the thermal conductivity of *.the rod material Consider a stainless steel spoon(k = 15.1 W/m.K), partially...
A long steel bar (length L-100 m, elastic modulus E = 2x 1011 N/m2, density ρ...

A long steel bar (length L-100 m, elastic modulus E = 2x 1011 N/m2, density ρ 7850 kgm3) of unit cross section is held at one end while hanging freely inside a deep pit and you are asked to estimate the longitudinal stress and displacement along the length of the bar Assuming linear elastic behavior, the internal elastic energy U of the hanging bar is given by the expression where z is the distance from the top of the pit...

2. The south pole of a bar magnet is brought close to a 250s-turn/m, 60-cm long...

2. The south pole of a bar magnet is brought close to a 250s-turn/m, 60-cm long copper solenoid with a radius of 7 cm. The wire has a cross-sectional area of 1.33 x 105 m² and is being kept at 25°C. Copper wire has a resistivity of 1.72 x 10% Om at 20°C and a temperature coefficient of resistivity of 3.9 x 10C!. If there is an induced current of 3 A after 0.2 s, what is the strength and...