Problem 6. (15 pts) A pressure vessel with an inside diameter of d-575 mm and a...
Problem 5. (20 pts) A vertical propane tank with an outside diameter of D 300 mm and a wall-thickness of t-9 mm is subjected to a horizontal force of P 41 kN. The gage pressure inside the tank is 7 MPa. [D-300 mm, te9 mm, P 41 kN] a) Determine the maximum normal stress at point K b) Determine the shear stress produced by the applied force. c) Determine the maximum shear stress in the 3d stress element.
A cylindrical tank holding oxygen at 5000 kPa pressure has an outside diameter of 500 mm and a wall thickness of 10 mm. It has been determined that a critical point on the tank is subjected to the tensile stress of 465 MPa in x-direction, compressive stress of 350 MPa in y-direction and shearing stress of 600 MPa. By using Mohr’s Circle; Sketch the plane stresses element for the critical point. Determine the principal stresses and their locations. Determine the...
A cylindrical tank holding oxygen at 4000 kPa pressure has an outside diameter of 500 mm and a wall thickness of 10 mm. It has been determined that a critical point on the tank is subjected to the tensile stress of 464 MPa in x-direction, compressive stress of 340 MPa in y-direction and shearing stress of 600 MPa. By using Mohr’s Circle; Sketch the plane stresses element for the critical point. Determine the principal stresses and their locations. Determine the...
P Problem 3 (30 pts): Combined Loading A pressurized cylindrical air tank is subjected to a force P at a collar B. The tank has an inner diameter (d= 160 mm) with wall thickness (t = 6 mm). The gage pressure inside the tank is p = 5 MPa and the applied force is P=9.5 kN. B 450 mm (a) Determine the maximum tensile stress 0 [MPa], maximum compressive stress oc [MPa] and maximum shear stress Tmax [MPa] at point...
P B Problem 3 (30 pts): Combined Loading A pressurized cylindrical air tank is subjected to a force Pat a collar B. The tank has an inner diameter (d = 160 mm) with wall thickness (t = 6 mm). The gage pressure inside the tank is p = 5 MPa and the applied force is P=9.5 kN. (a) Determine the maximum tensile stress o [MPa], maximum compressive stress oc [MPa] and maximum shear stress Tmax [MPa] at point a. (b)...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm wall thickness is fabricated from a 1.2 m length of spirally welded pipe AB as shown. Tank gauge pressure is 4 MPa and centric axial forces P and P1 of 240 kN act through rigid end plates. Determine: (a) Net longitudinal and hoop stresses. (b) Normal stress acting perpendicular to weld and shear stress parallel to weld (show sketch of Mohr’s circle). (c) Determine the Factor of Safety...
A pipe with an outside diameter of 175 mm and a wall thickness of 6 mm is subjected to the loadings shown in the figure below. Р. H For this analysis, use the following values: Distances, Loads, and Moments. a = 400 mm Px = 40.5 kN Py = 68.5 kN T = 35 kN-m (a) Calculate the maximum in-plane shear stress Tmax at point Hon the outer surface of the pipe if there is no internal pressure (i.e.,p-OkPa). (Note:...
solid mechanics plz show yhe correct steps to the answers plz Problem 2 10 pts A cylindrical pressure vessel with wall thickness t-5 mm and inside radius r 150 mm is design to hold high pressure. The vessel design requires a safety factor against yielding Xo -2, and leak-before-break with a safety factor X-5 on the critical crack length; that is, the critical crack length ce must be at least Xt. Calculate the maximum pressure, p, if the vessel is...
please make your answers clear and organized . Problem 8.5-3 A cylindrical pressure vessel having radius r-300 mm and wall thickness t 15 mm is subjected to internal pressure p 2.5 MPa. In addition, a torque T120 kN-m acts at each end of the cylinder (see figure) (a) Determine the maximum tensile stress ?mix and the maximum in-plane shear stress Tmax in the wall of the cylinder torque T? 30 MPa and 76 MPa, respectively, what is the minimum required...
P B A pressurized cylindrical air tank is subjected to a force P at a collar B. The tank has an inner diameter (d = 160 mm) with wall thickness (1 = 6 mm). The gage pressure inside the tank is p = 5 MPa and the applied force is P = 9.5 kN. (a) Determine the maximum tensile stress o [MPa), maximum compressive stress oc [MPa] and maximum shear stress imax [MPa) at point a. (b) Repeat part (a)...