Q7: HOMEWORK 10 kg floating piston 4.0 cm- In the shown figure (poil-900 kg/m3) A. How...
How to solve question 44
s the anoint P, where FIGURE P13.40 gauge pressure of the the needle meets the wider chamber of the syringe? A 6 General Problems 41 Il As discussed in Section 13.4, a person' of titanium is 4.5 g/cm3. 125 g of titanium iss weight of the sph l The shaped into a cube. What is the length of each edge? You need to d s percentage of body fat suspend it R0 can be estimated...
A cylinder with a 16-cm-diameter piston contains gas at a pressure of 3.0atm. a) How much force does the gas exert on the piston? b) How much force does the environment exert on the piston? c) The gas expands at constant pressure and pushes the piston out 10cm. How much work is done by the environment? d) How much work is done by the gas?
Part B A cylinder with a 16-cm-diameter piston contains gas at a pressure of 3.0 atm How much force does the environment exert on the piston? 2040 SubmitP Previous Answers Request Answer X Incorrect; Try Again; 9 attempts remaining Part The gas expands at constant pressure and pushes the piston out 10 cm. How much work is done by the environment? Submit Request Answer
A 4.00 cm x 4.00 cm x 4.00 cm cube of density 920 kg/m3 is floating at rest at the top of a beaker of cross sectional area 100 cm2 with 500 mL of water in it. 500 mL of oil of density 900 kg/m3 is added to the top of the beaker, and the cube is observed to float completely submerged, unevenly straddling the boundary between the oil and water. a. Draw a picture showing the beaker, layers of...
As shown in the figure below, 0.5 kg of water is contained within a piston-cylinder assembly at 100°C. The piston has a mass of 90 kg and is free to move smoothly in the cylinder. The local atmospheric pressure and acceleration of gravity are 100 kPa and 9.81 m/s2, respectively. g=9.81 m/s2 Patm = 100 kPa Piston Water at 100°C A = 0.01 m2 For the water, determine the pressure, in kPa, and volume, in cm?
Air contained within a vertical piston-cylinder assembly is shown in Figure 1. On its top, the 10-kg piston is attached to a spring and exposed to an atmospheric pressure of 1 bar. Initially, the bottom of the piston is at x = 0, and the spring exerts a negligible force on the piston. The valve is opened and air enters the cylinder from the supply line, causing the volume of the air within the cylinder...
AIR A 45-cm piston-cylinder system contains 0.65 m3 of air. At the position shown, there is no force in the spring (k = 2.5 kN/m), and the pressure and temperature are 1,100 kPa and 350 °C respectively. Heat is transferred to the air until its volume increases 30 %. Determine: a) The final temperature and pressure of the air in °C; b) the change in total internal energy of the air in kJ.
In the figure, the large piston on the left has a diameter of
D1 = 9.00 cm.
The small piston on the right has a diameter of
D2 = 4.00 cm.
A lever arm pivot is located at a = 5.00 cm to
the left of the small piston.
A small cylinder hangs from the end of the lever arm a distance
of b = 25 cm to the right of the small piston.
In the absence of friction, determine...
A) A 4.00 cm x 4.00 cm x 4.00 cm cube of density 920 kg/m3 is floating at rest at the top of a beaker of cross sectional area 100 cm2 with 500 mL of water in it (1 mL of water has a volume of 1 cm3 or 1x10-6 m3 ). 500 mL of oil of density 900 kg/m3 is added to the top of the beaker, and the cube is observed to float completely submerged, unevenly straddling the...
Part A Review The 50 kg ciroular lead piston shown in (Figure 1) floats on 0.21 mol of compressed air What is the piston height h if the temperature is 30 C Express your answer with the appropriate units. hValue Units Submit Request Answer Figure 1 of1 ▼PartB How far does the piston move the temperature is ncreased by 10007 Express your answer with the appropriate units 1 atm 0 kg Units 30℃ Submit Request Answer 10 cm