Sketch the output of the following circuits given the input shown (100 Hz sine wave of...
Sketch the output of the following circuits given the input shown (100 Hz sine wave of 10 +3V IN914s IN 2.2k 1k 0V IN OUT IN914 OUT f= 100 Hz
The oscilloscope display below is connected to a sine wave of 100 Hz frequency and 4 volt amplitude, 100 us seconds/div, and 2 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal into focus so that it displays a sine wave? The oscilloscope display below is connected to a sine wave of 150 Hz frequency , 2 ms seconds/div, and 1 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal...
8. vin ?s a 3V peak-to-peak 1 Hz sine wave with +2v dc offset. Find vout pp peak-to-peak voltage Rc 3k o Vout in lk 20 points
Question 2: (10 points) In the full rectifier circuit shown, the input is a sine wave with a frequency of 50 Hz and an amplitude of 6 V. 1 For this circuit, sketch on the figure below the output voltage across the resistor R assuming ideal diodes. Show the time scale on the figure. Sketch also on the same figure a typical output when a capacitor is placed in parallel with the resistor. vou TOU to ts. ti to 0.00...
Question 6: Draw the output wave form for the following circuits. The input is a 10V peak sin wave and Yiotall diodes are same 1V ▲Vo Dilv R1 ▲Vo Iv. D1 in +out 10 '61完以
Determine the following about the sine wave ac voltage shown: a. Amplitude and peak-to-peak voltage. b. Period, frequency and angular frequency (o). c. Write the sine wave equation for the ac voltage. d. Calculate the voltage at 2.5us. e. Calculate the voltage at 2ms. volts (v) 7 2 14 0 8 10 12 time (us
Given taple 3,please solve for part(d)-part(f) hange the mode on the signal generator to sine-wave, with a peak-to-peak amplitude of eak-to-peak amplitude of the voltage across the capacitor for various frequencies (100, 4 500, 2000, and 5000 Hz), and complete Table 3, (0.4%) Table 3 Frequency (in Hertz) 100 400 800 1000 1500 2000 5000 Vc (peak-to-peak) ange the mode on the signal generator to sine-wave, with a peak-to-peak amplitude of 2V. Measure the 1500, 2000, and 5000 Hz), and...
2. Diode circuits and output waveforms. (a) Sketch the output waveforms expected when a 100Hz, 6Vp sine wave is applied to each of the circuits shown. Label important voltage levels and time values. Your plots should be large enough, at least 4 to 6 inches on a side, and semi-quantitative to represent accurately the output waveform. Note: the input signal is ap- plied to the left side of the circuit and the output taken from the two terminals on the...
(5pts) 11. A 0.5V peak-to-peak 1kHz sine wave with a 100mV DC offset is provided as the input into a non- inverting operational amplifier with a gain of 20. If the output of the op-amp is read using an oscilloscope with AC coupling, then the value is close to a. 2V DC b. 2V peak-to-peak 1kHz sine wave c. 10V peak-to-peak 1kHz sine wave with 2V DC offset d. 10V peak-to-peak 1kHz sine wave only (5pts) 12. Which of the...
Consider the circuit as shown below. If Vp-10pp 1 kHz sine wave, Sketch the output voltage. VB 0.7V, matching diodes. What is the frequency of the output wave form: Vp Tirne Time