Sketch the output of the following circuits given the input shown (100 Hz sine wave of...
Sketch the output of the following circuits given the input shown (100 Hz sine wave of 10 Volts peak-to-peak amplitude). +3V IN 2.2k IN914s lk 1QV IN OUT OUT IN914 f 100 Hz -3V
1. For the 4 circuits shown below, sketch the output waveform for a 1V peak, 1kHz, sinusoidal wave in put signal. Assume the diodes are ideal and they exhibit ON-OFF switch model behaviour. Create an ideal diode model in LT-Spice with the following specification [.model IdealDiode D(Ron=0.1m Roff=100G Vfwd-0.0) ] simulate the circuit and verify the output waveform. Vin Vout Vin Vout 1k 1k (a) (b) 1k Vin 1k Vin Vout Vout ww 1k (c) (d) KH
1. For the...
Draw a circuit to output the following wave as 1V
pk-pk sine wave centered at 0V and output to be out of phase
180degrees with respect to input.
Problem #5 [10 points]: Design a circuit with the following criteria. Assume existence of +5V power supply. Draw your circuit and show your work. i. Input signal that operates between Vin -5V- +5V, and capable of sourcing or sinking 500 x 10^-6 A. ii. Output signal nominally outputs between Vout 0V 5V,...
Question 2: (10 points) In the full rectifier circuit shown, the input is a sine wave with a frequency of 50 Hz and an amplitude of 6 V. 1 For this circuit, sketch on the figure below the output voltage across the resistor R assuming ideal diodes. Show the time scale on the figure. Sketch also on the same figure a typical output when a capacitor is placed in parallel with the resistor. vou TOU to ts. ti to 0.00...
2. Diode circuits and output waveforms. (a) Sketch the output waveforms expected when a 100Hz, 6Vp sine wave is applied to each of the circuits shown. Label important voltage levels and time values. Your plots should be large enough, at least 4 to 6 inches on a side, and semi-quantitative to represent accurately the output waveform. Note: the input signal is ap- plied to the left side of the circuit and the output taken from the two terminals on the...
Question 6: Draw the output wave form for the following circuits. The input is a 10V peak sin wave and Yiotall diodes are same 1V ▲Vo Dilv R1 ▲Vo Iv. D1 in +out 10 '61完以
Consider the circuit as shown below. If Vp-10pp 1 kHz sine wave, Sketch the output voltage. VB 0.7V, matching diodes. What is the frequency of the output wave form: Vp Tirne Time
24) For the three circuits (a), (b) and (c) shown below, the waveform of input voltage vy is given as shown below. For each circuit, sketch the waveform of output voltage vo for the given input voltage . Label the most positive and most negative output levels. Assume all diodes are ideal (vp- 0) and CR>> T. (10 points) +10 V-- -10 V TI ms (3 points) (b) o- (3 points) 3V (4 points) DH
The oscilloscope display below is connected to a sine wave of 100 Hz frequency and 4 volt amplitude, 100 us seconds/div, and 2 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal into focus so that it displays a sine wave? The oscilloscope display below is connected to a sine wave of 150 Hz frequency , 2 ms seconds/div, and 1 volts/div. What control(s) on the oscilloscope need to be adjusted to bring this signal...