Question 6: Draw the output wave form for the following circuits. The input is a 10V...
Sketch the output of the following circuits given the input shown (100 Hz sine wave of 10 Volts peak-to-peak amplitude). +3V IN 2.2k IN914s lk 1QV IN OUT OUT IN914 f 100 Hz -3V
Sketch the output of the following circuits given the input shown (100 Hz sine wave of 10 +3V IN914s IN 2.2k 1k 0V IN OUT IN914 OUT f= 100 Hz
1. For the 4 circuits shown below, sketch the output waveform for a 1V peak, 1kHz, sinusoidal wave in put signal. Assume the diodes are ideal and they exhibit ON-OFF switch model behaviour. Create an ideal diode model in LT-Spice with the following specification [.model IdealDiode D(Ron=0.1m Roff=100G Vfwd-0.0) ] simulate the circuit and verify the output waveform. Vin Vout Vin Vout 1k 1k (a) (b) 1k Vin 1k Vin Vout Vout ww 1k (c) (d) KH
1. For the...
Draw a circuit to output the following wave as 1V
pk-pk sine wave centered at 0V and output to be out of phase
180degrees with respect to input.
Problem #5 [10 points]: Design a circuit with the following criteria. Assume existence of +5V power supply. Draw your circuit and show your work. i. Input signal that operates between Vin -5V- +5V, and capable of sourcing or sinking 500 x 10^-6 A. ii. Output signal nominally outputs between Vout 0V 5V,...
Please note that D4 is the one that was destroyed not D1.
Please I posted this but they answer it differently
QUESTION (2) Due to an abnormal operating condition, Diode D4 in this full-wave rectifier circuit was suddenly destroyed, and stopped Vconducting in both forward and reverse directions (i.e. open circuit) C- R Assume that all other diodes are ideal with zero forward voltage drop and that the time constant RC- 5 ms. stt) 10V For a 1 kHz triangular...
do appreciate the process in details and neat
(b) The circuit shown in Figure 2 utilizes two diodes, Di and D2, a R, resistor R1 = 10 Ω. Assume a piecewise linear (PWL) model for the diode that has VD 07 and r-5 Ω. Draw the output voltage, vo, as function of the input voltage, Vin, characteristics of this circuit at point assuming the input voltage has a peak-to-peak voltage of 3 Volt. There is no need to draw the...
QUESTION (2) The diodes are ideal except with an on-voltage of 0.7V. The input voltage source vIN is a 100Hz, 50% duty cycle square-wave with voltage levels of OV and +10V. The load resistance, R = 1002 DL D a) If the ripple voltage, V 0.5V, sketch the output waveform for several input cycles. What is the average DC output voltage vo + D. C R (6 points) Vo VIN b) What would be the minimum value of C (in...
Question 4 The input signal to the circuit below is a Triangle wave with a peak to peak Vin of 10 V Determine the ideal peak to peak output voltage signal. The Frequency is 1 kHz Note: At 0.5 Tp Amplifier Parameters Vin R1 10 Ypg R1 10 K2 0.01 uF C1 Veu Ereg 1 1H2 Vout Note 4 Vpp, Triangle Wave 4 Vpp, Square Wave 2 Vpp, Square Wave 2 Vpp, Triangle Wave
The output of the following circuit is affected by: R1 Out WYD1 D2 Out D1 v1 2K 1N4148 V2 1N4148 T 1N4148 1N4148 V3 3.6V 4.8V SINE(O 10 1k) Select one: The branch that contains D2. because it has higher DC voltage (4.8V) The branch that contains diode D1 because it has lower DC voltage (3.6V) Both branches (that contain D1 and D2) are parallel with V= 3.6V. Hence both branches are affecting V(out) Both branches (that contain D1 and...
Question 3 a) Following is an incomplete circuit drawing of a full-wave rectifier. Copy the drawing and complete it by placing 4 diodes in the correct locations and orientatıons dc Output 10V b) Briefly describe the function and operation of the resulting circuit. Include an example illustrating an application of this circuit c) St ating any necessary assumptions, what is the instantaneous maximum voltage at the output of the circuit in part a) d) Given a supply of diodes and...