Hello please explain step by step
Hello please explain step by step Problem 1 Given the following specifications: 1- Center Frequency of...
BY CLEAR STEP AND LINE AND DEATILS PLEASE!!!! A. Calculate the center frequency (f0), two cut-off frequencies (fC1 and fC2), and bandwidth (β) in Hertz, for the circuit in Figure 11.7. B. (((BY PSPICE ))) Simulate the circuit of figure 11.7 using ac sweep with a Vac source at 1 V amplitude; plot the magnitude of the output voltage (Vo) C.Repeat Step B for the circuit of figure 11.7, using R = 3.2 kΩ D. Repeat Step B for the...
Please help me solve this urgently [15%] input voltage is given by 1. what is th e transfer function and the output voltage for the circuit shown below? The Vin(1)-10+8cos(5Oxt-90") +4cos(100t +60°). 40 mH Problem 1 2. [1596] Design an R-L-C parallel resonance band-pass filter for the frequency components of 2kHz, 8 kHz, and 14 kHz which are allowed to pass. Assume that the bandwidth is 2 kHz wider than the minimum bandwidth required. Find the related values for R...
Design an active unity-gain bandpass filter with center frequency 750 Hz and bandwidtg 250 Hz and with 0.1 μF capacitor, R1=6.4kΩ, R2=377Ω, and R3=12.7kΩ. a)Discuss the circuit response with support of a Bode magnitude plot. b) Assume next that a load R_L is connected to the output of the network at the terminal Vo(s). How does the frequency response of the loaded configuration change? c) Consider a broadband bandpass op amp filter with center frequency 2.4 kHz and bandwidth 800...
Please answer the problem below for all parts . Please show all work and write clearly. The answers are below, but work must be shown to get to the answers. Thanks. answers 8.14. Design a second-order digital bandpass Chebyshev filter with the following specifications: Center frequency of 1.5 kHz Bandwidth of 200 Hz 0.5 dB passband ripple Sampling frequency of 8,000 Hz a. Determine the transfer function and difference equation. 8.14 a. 0.1815-0.1815z2 1-0.6265z +0.6370z y(n)-0.1815x(n)-0.1815x(n-2)+0.6265y(n1) 0.6370y(n-2) 8.14. Design a...
Problem 4 For the circuit in Fig. 3, frequency w a) Draw the impedance model of the circuit for a source b) Convert the voltage lence) and redraw the impedance model; (using Thevenin and Norton equiva- Source into a current source c) Using the results from part (b), derive the expressions to determine the resonance frequency of the circuit in terms of the circuit parameters; e) We would like to have a resonance peak gain frequency of fo equal to...
The center frequency is not given. I believe that it must be find based on the body plot. Problem 6:The Bode plot for a passive series RLC bandpass filter is shown in Fig. 2. This filter was built from a 10 μ F capacitor. What is the filter's center frequency, wo, and its quality factor,昱? If you wanted to double the filter's center frequency without changing its quality factor, using the same 10 pu F capacitor, then how would you...
1. Design a parallel RLC bandpass filter, derive the transfer function H(s). Compute the center frequency, Wo. Calculate the cutoff frequencies Wej and Wc2, the bandwidth ß, and quality factor, Q. Compute values for R and L to yield a bandpass filter with a center frequency of 5kHz and a bandwidth of 200Hz, using a 10nF capacitor. (25 points) 1. Design a parallel RLC bandpass filter, derive the transfer function H(s). Compute the center frequency, Wo. Calculate the cutoff frequencies...
Q.6 For the series circuit in Figure given below, Determine Assume R -500n Vin-10V . The center frequency (f) b. The output voltage magnitude at (f) c. The bandwidth (BW )for the filter d. Draw the output response curve showing the maximum voltage, center frequency and the voltage where the BW is measured 150Ω 100μH Q.6 For the series circuit in Figure given below, Determine Assume R -500n Vin-10V . The center frequency (f) b. The output voltage magnitude at...
1) Design a low-pass RC device with the following specifications: a) Input x(t) and output y(t) b) Bandwidth which is defined as the range of frequencies (from 0 Hz to ??, the − 3dB point ) allowed to pass through without significant attenuation = 100Hz c) Static gain = 14dB d) The system has −20 dB/decade rolloff at high frequencies (thus first-order LP filter) Assume that you have one and only one resistor value available to you, and that resistance is...
Please provide step by step solution with all formulas. Q1. A series RLC circuit as shown in Figure Q1 has a resonant frequency,o, of 200t rad/s, inductance, L = 50 mH and the quality factor, Q = 15, and it is driven by a voltage source, Vin(t) = 220sin(ot) R L m Vin(t) с Figure Q1 Calculate: (a) The value of R and C. [4] [6] [4] (b) The energy stored, the average power and the energy dissipated per cycle....