This is the figure that accompanies the problem.
Please solve with explanations.
This is the figure that accompanies the problem. Please solve with explanations. raised ITUNI WIT SANTUOI...
1. The three ropes in the figure are tied to a small, very light
ring. Two of the ropes are anchored to walls at right angles, and
the third rope pulls as shown. What are T1and T2, the magnitudes of
the tension forces in the first two ropes?
A. T1=
B T2=
3. The two angled ropes used to support the crate in the figure
below can withstand a maximum tension of 1700N before they
break.
A. What is the...
The two angled ropes used to support the crate in the figure below an withstand a maximum tension of 1100 before they break. What is the largest mass the ropes cansupport?
Part A A 500 kg steel beam is supported by the two ropes shown in (Figure 1) Calculate the tension in the rope. Express your answer to two significant figures and Include the appropriate units. The rope can support a maximum tension of 2700 N . Is this rope strong enough to do the job? Choose the correct answer and explanation. Yes. The tension in the ropes exceeds the maximum value, but since we have two ropes they can support...
Forces and Newton's LAWS WU PHYS 1107 - General Physics I ) An 9.0 kg mass (M) is placed on a horizontal surface. A massless rope runs over a frictionless massless pulley which connects the mass M to a 6.5 kg mass (m) that hangs vertically. a) What is the acceleration of the vertical mass if the horizontal surface is frictionless? b) What is the tension in the rope if the horizontal surface is frictionless? Now assume that the horizontal...
Note: help me solve problem 1.33 only using Fig
P1.33
Answer:
Shear stress A : 3670psi
Shear stress B : 4320psi
Thank you
22 CHAPTER 1 Stress 45° 10 m 200 lb 6 ft l 12 in. 2 ft o A 4 ft 3 ft 36 in. FIG. P1.33 FIG. P1.34 FIG. P1.35 1.33 The bracket is supported by 1/2-in. diameter pins at A and B (the pin at B fits in the 45° slot in the bracket)....
Fun with Bulk Density!!! Solve this problem • You want to pick up topsoil for your garden. Assume that the B, for the topsoil is typical of a medium textured loam soil - 1.25 Mg/m3 • You would like to load the material in a standard pickup truck that has a load capacity of 680 kg (1500 lb ) and a bed volume of 1.85 m3 (65 ft3) • Can this truck receive a full load (entire bed volume filled)...
A worker stands a distance
d = 0.250 m
from the left end of a beam as shown in the figure. The beam is
supported by three ropes. Find the tension in each rope (in N).
Assume the beam is uniform, with length L = 2.00 m and
mass 34.0 kg, and the weight of the worker is 710 N. (Due to the
nature of this problem, do not use rounded intermediate values in
your calculations—including answers submitted in
WebAssign.)...
can someone please help me solve this problem?
ure < 1 of 1 450N LA 300 Nm 0.6 m 45 0.4 m 0.8 m B 0.4 m Part A Determine the components of reaction acting at the smooth journal bearing A.(Figure 1) Enter the x, y, and z components of the force separated by commas. IVO AED 0 vec ? A... Ay, Az = N Submit Request Answer Part B Determine the components of reaction acting at the smooth journal...
Use the worked example above to help you solve this problem. A solid, frictionless cylinder reel of mass M 2.60 kg and radius R = 0.397 m is used to draw water from a well (see Figure (a)). A bucket of mass m = 2.19 kg is attached to a cord that is wrapped around the cylinder. (Indicate the direction with the sign of your answer.) (a) Find the tension l' in the cord and acceleration a of the bucket....
I don't know the question number of 3,4,7. Please solve this
problem.
I have attached all the data that I need to solve the problem
as a photo.
3. Someone in your company proposes to use an existing square pitch 150 mm diameter plasticating single screw extruder as a mixing device for a 40/60 PS/PP polymer blend. The metering section is 5 turns long and has a channel depth of 10 mm. Will dispersion of the polystyrene occur for a...