For the given circuit, Solve for VOVO, IDID, ILIL, and IZIZ for
the following cases. Take VS=1VS=1 VV, VD=0.3VD=0.3 VV, RD=10RD=10
ΩΩ, and VZ=0.7VZ=0.7 VV.a)R1=800R1=800 ΩΩ,
RL=200RL=200 ΩΩ
b)R1=500R1=500 ΩΩ, RL=500RL=500 ΩΩ
c)R1=200R1=200 ΩΩ, RL=800RL=800ΩΩ
d)R1=50R1=50 ΩΩ, RL=950RL=950 ΩΩ
VOVO VV | IZIZ AA | ILIL AA | IDID AA | |
a) | ||||
b) | ||||
c) | ||||
d) |
For the given circuit, Solve for VOVO, IDID, ILIL, and IZIZ for the following cases. Take...
For the given circuit, Solve for VO , ID , IL , and IZ for the following cases. Take VS=1 V , VD=0.25 V , RD=15Ω , and VZ=0.7 V .a) R1=800 Ω , RL=200 Ω b) R1=500Ω , RL=500 Ω c) R1=200Ω , RL=800Ω d) R1=50Ω , RL=950Ω (1 point) Ov: 141 ŠR lo vo @ 0 For the given circuit, Solve for Vo, ID, IL, and Iz for the following cases. Take Vs = 1V, Vp = 0.25...
Solve for I1I1 and I2I2 in this circuit with 3 identical transistors if VCC=15VCC=15 VV, R=500R=500 ΩΩ, and β=100β=100.I1=I1= AA I2=I2= A (1 point) V cc = By UBC Engineering Solve for I and 1, in this circuit with 3 identical transistors if Vcc = 15 V, R= 500 S2, and B = 100.
Q1: Use the following Data to Design the circuit Below: RL RL (2) Vo (with) (V) Vo (Without) 300 0.6 0.6 800 1.45 1.45 1.3k 2.167 2.167 7.8k 5.1 . 24 Open circuit 5.5 0 6 1 a) Design the circuit by Finding the value of Rs, Vs, and Vz. b) Zener at RL = 7.8k 2 acts as..........
(b) Compute the voltage gain, input and output impedance for the following circuit if ß = 150 and VBEQ = 0.7 V, V1 = 26 mV. A + 10 V 40 ΚΩ R1 4 ΚΩ Ci CO Vs R2 VO 60 ΚΩ 5 ΚΩ RE RL 1ΚΩ
Solve: For the circuit below, using a 2N7000 N-Channel MOSFET, VDD Of 20 V, V 1V and (kn'w/L)- 100umohs, calculate Vo, Vo and Vs and lo. Then, set an input signal Vin 25mV peak amplitude with a frequency of 1kHz. Calculate the voltage gain (Von/Vn) + VDD RG1 V 390 kn RD VRD 堲 C. C1 M1 IG=01- 10μ5 2N7000/PLP 2N7000/PLPRLoad VGS V, GS RS 15F 0.47k CS RS CS DC measurements: Calculated AC measurements: A VV Calculated
Q2. For the op-amp circuit as shown below, given that RS = 49.5 k, RL = 12 k 2, R1 = 10 kO, R2 = 9 ㏀, R3 = 7.5 ko, R4 = 5 ㏀R5 = 2.2 k2 Ry vo Ry Ri Rs (a) Determine the voltage gain G1-vo1/vs: Submit Answer Tries o/5 (b) Determine the voltage gain G2-vo/vs: Submit Answer Tries o/5 Q3. For the op-amp circuit shown below, find the value of VO, where R1 = 20 Ω,...
#4 The accompanying circuit shows a 4-resistor biased JFET transistor Determine the values of Rp and Rs so that the Q-point is equal to, VDsq 10 V and IDg 5 mA . For the JFET take IDss = 10 mA, VP =-5 V and λ 0 . The circuit parameters are, R1-740 k, R2-22 1.85 ka, Rs-85 ㏀ and RL-3.5 ㏀. Take the power supply VDD 24 V 2- Vo R1 Vi R2 Signal generator 4-In reference to the circuit...
Problem 2 (15 points) Use the circuit given to answer the following questions. a. On the figure, identify and label the different currents in this circuit. Be sure to give them directions. [2 point] b. Use Kirchoff's loop rule to write down equations for all 3 possible loops that could be used to solve for the currents in this circuit (You do not need to solve them!) 19 points = V, - IR, - V2 - IR4 so Vo vz...
(50 pts) For the following circuit, solve for R, Ra, Rs, R, and Rs given the specified voltages and current. The values of R will be 600Ω. 1000Q, 5000Q, or 10K. Remember that tolerance will be a factor in your calculations. 4. 0.00311A 500 Ω 600 Ω R1 Ω O Node 1-17.03 V 5,000 Ω 10 kΩ R2Ω Node 2-10.81 V R3 Ω 36 V 600 Ω 1ΚΩ Node 3-7.78 V Node 4 -4.95 V , 600 Ω O Node...