For the given circuit, Solve for VO , ID , IL , and IZ for the
following cases. Take VS=1 V , VD=0.25 V , RD=15Ω , and VZ=0.7 V
.a) R1=800 Ω , RL=200 Ω
b) R1=500Ω , RL=500
Ω
c) R1=200Ω ,
RL=800Ω
d) R1=50Ω ,
RL=950Ω
For the given circuit, Solve for VOVO, IDID, ILIL, and IZIZ for
the following cases. Take VS=1VS=1 VV, VD=0.3VD=0.3 VV, RD=10RD=10
ΩΩ, and VZ=0.7VZ=0.7 VV.a)R1=800R1=800 ΩΩ,
RL=200RL=200 ΩΩ
b)R1=500R1=500 ΩΩ, RL=500RL=500 ΩΩ
c)R1=200R1=200 ΩΩ, RL=800RL=800ΩΩ
d)R1=50R1=50 ΩΩ, RL=950RL=950 ΩΩ
VOVO VV
IZIZ AA
ILIL AA
IDID AA
a)
b)
c)
d)
(1 point) Ovo 22 LR 16 vo @oe By UBC Engineering For the given circuit, Solve for Vo, ID: Il, and Iz for the following cases. Take Vs =...
For the given circuit; a) Determine V, IL, IR and Iz b) For R_ = 1k02, find V, IL, IR and Iz. C) For proper regulator operation, determine the minimum value of RL. R W 1 ke 2 + Iz IR RL 18 V PZmar V2 = 10 V = 150 mW 3kΩ VL For the given circuit; B = 100. Determine VBQ, VEQ, 'EQ, V CEQ, Te Replace the transistor with the r small signal equivalent model. 1 Determine...
Q1: Use the following Data to Design the circuit Below: RL RL (2) Vo (with) (V) Vo (Without) 300 0.6 0.6 800 1.45 1.45 1.3k 2.167 2.167 7.8k 5.1 . 24 Open circuit 5.5 0 6 1 a) Design the circuit by Finding the value of Rs, Vs, and Vz. b) Zener at RL = 7.8k 2 acts as..........
Q2. For the op-amp circuit as shown below, given that RS = 49.5 k, RL = 12 k 2, R1 = 10 kO, R2 = 9 ㏀, R3 = 7.5 ko, R4 = 5 ㏀R5 = 2.2 k2 Ry vo Ry Ri Rs (a) Determine the voltage gain G1-vo1/vs: Submit Answer Tries o/5 (b) Determine the voltage gain G2-vo/vs: Submit Answer Tries o/5 Q3. For the op-amp circuit shown below, find the value of VO, where R1 = 20 Ω,...
Determine iL(t) for in the circuit of Fig. P12.21 for t =45 ms ,
given that the switch was opened at t = 0 after it had been closed
for a long time, vs = 12 mV, R0 = 5 Ω , R1 = 10 Ω,R2 = 20 Ω, L =
0.2 H, and C = 6 mF. Give the current in micro Amperes, Hint, the
initial conditions are zero and the steady state current in the
inductor will be...
Question 3: For the below circuit, given that Rs=201, a=0.3, RL=250N. RA 1,(t) a: 1 iz(t) + + V (t) R IR, Answer the following questions a. If V2(t) = 110cos (250t) v calculate v1 b. Calculate the input impedance R1 C. Calculate the currents 11 and 12 d. Calculate the value of Vs
1. Response of the RL circuit - After having been in position 1 for a long time, the switch in the circuit below is moved to position 2 at the time t = 0. Given that Vo = 12 V, R1 = 3092, R2 = 12092, R3 = 6022 and L = 0.2 H, determine; a) iz(0-) and vi(0-) b) iz(0) and vi(0) c) il(o) and vi(0) d) il(t) for t20 e) vi(t) for t20 RU AN
(a) The following circuit shows a linear
voltage regulator. Assuming the zener diode has specifications (VZ
= 2.5 V, IZ = 60 mA), select adequate resistor values to provide a
regulated output voltage Vo = 10 V from an unregulated voltage Vi =
15V.
(b) Calculate the power efficiency of the
regulator when a load RL = 10Ω is connected to the regulator
output.
(c) Briefly explain the terms “dropout”, “line
regulation”, and “load regulation”, as they apply to voltage...
please show steps, and solve asap
BEE 433 Electronic Circuit Design Problem Set #1 Due date: Answer the following problems and Circle the answers. 1.1 (Fig. 1.1 from the textbook) In the voltage amplifier circuit of Fig. 1.1, let vs = 100 mV, Rs = 100 k 52, Vi = 75 mV, RL = 10 S2, and vo = 2 V. If connecting a 30-S2 resistance in parallel with RL drops vo to 1.8 V, find Ri, A., and R....
Determine il(t) for in the circuit of Fig. P12.21 for t=16 ms, given that the switch was opened at t= 0 after it had been closed for a long time, vs = 12 mV, RO = 50, R1 = 10 A, R2 = 20 . L = 0.2 H, and C = 6 mF. Give the current in micro Amperes, Hint, the initial conditions are zero and the steady state current in the inductor will be 800 microAmps. Correct Answer:...