The output voltage of a particular op-amp increases 8V in 12 micro seconds in response to...

Question

Question

The output voltage of a particular op-amp increases 8V in 12 micro seconds in response to a step input voltage. The slew rate is ?

Answer 1

Answer #1

change in the vallenge DV= 8v. change in the tire = 12 meseci The slew rak is =- slew rake change in the valtare change in th

Answer 2

Similar Homework Help Questions

A. (10 pts) Implement the voltage amplifier shown below using an ideal op amp circuit. You have o...

a. (10 pts) Implement the voltage amplifier shown below using an ideal op amp circuit. You have one op amp available for this circuit, and a range of resistors with values from 1 kΩ to 100 ka. Draw the schematic of your op amp circuit, labeling resistor values. Make sure the gain, input resistance, and output resistance of your circuit matches the model in the schematic. R=012 *100v, RL 100 b. (5 pts) Your amplifier circuit should have a frequency...
For the Op-Amp in the figure below find the magnityde of the output voitage Vout R....

For the Op-Amp in the figure below find the magnityde of the output voitage Vout R. 100 kΩ Op-amp parameters +12 V AOL = 80,000 22 Mo Tout 75 0(maximum) Slew rate-8 V/μs Rin 100 kΩ in 16 Vpp RL -12 V
9. In this ideal op amp circuit: a) Find the output voltage vo in terms of...

9. In this ideal op amp circuit: a) Find the output voltage vo in terms of the input voltage v. b) The op amp is supplied by +10v and -10v. If0 V15v, find the range of the output voltage vo. (15 pts.) 10 k2 5 kQ 10V -10V ng 2.5v(+ 0)

design a bistable multivibrator using an op amp with+- 10v output saturation voltages L+=L-=8v and a...

design a bistable multivibrator using an op amp with+- 10v output saturation voltages L+=L-=8v and a hysteresis width of 160 mv
For this op Amp find the equation for the output voltage Vout in terms of input...

For this op Amp find the equation for the output voltage Vout in terms of input voltage Vin. (Ohms law, KVL, KCL) La Vin Q, Vout
Design a two stage op amp with the following specifications Design Specifications Supply voltage ...

Design a two stage op amp with the following specifications Design Specifications Supply voltage Maximum power dissipation DC Gain Phase Margin Unity gain-bandwidth Slew Rate PSRR CMRR Load Capacitance (C) Input Common Mode Range 3.3 V 10 % 5 mW 100 dB >60 >100 MHz >20 V/usec >70 dB >70 dB 10 pF Rail-to-rail ave Design a two stage op amp with the following specifications Design Specifications Supply voltage Maximum power dissipation DC Gain Phase Margin Unity gain-bandwidth Slew Rate...

Assume the op-amp below is used as a comparator circuit and that the op-amp is powered...

Assume the op-amp below is used as a comparator circuit and that the op-amp is powered by a bipolar +/- 15 V power supply. If the reference voltage Vref = -9 V and the input voltage is VI = 12 V, determine the output voltage, VO, of the op-amp. Assume the open-loop gain, A, is very large and consider saturation effects. Include units in your answer. VCC Vi V. + + Vref EE
5. Assume that the Op-Amp in the adjoining circuit is ideal, and find the output voltage...

5. Assume that the Op-Amp in the adjoining circuit is ideal, and find the output voltage V. in terms of the two input voltages V1 and V2 of the circuit. Ideal D2RE bi
1. Use supply voltage +/- 15V and design a comparator op-amp circuit where the output becomes...

1. Use supply voltage +/- 15V and design a comparator op-amp circuit where the output becomes maximum positive when the input is higher then 5V. 2. Sketch the output voltage relative to the input voltage of the circuit. 3. How can we get maximum negative output voltage when the input voltage is bigger then 5V?

QUESTION 1. (15 points) GIVEN THE INPUT WAVEFORMS, ASSUMING VOLTAGE VOur IDEAL OP AMP. DRAN THE OUTPUT IVEN THE INPUT WAVE A. DRAW THE OUTPUT VOLTAGE Voor ON TOP OF INPUT SIGNAL V +V B. DRAW THE...

QUESTION 1. (15 points) GIVEN THE INPUT WAVEFORMS, ASSUMING VOLTAGE VOur IDEAL OP AMP. DRAN THE OUTPUT IVEN THE INPUT WAVE A. DRAW THE OUTPUT VOLTAGE Voor ON TOP OF INPUT SIGNAL V +V B. DRAW THE OUTPUT VOLTAGE Vour ON TOP OF INPUT SIGNAL V +V +V Vi. C. HOW MUCH VOLTAGE WOULD HAVE TO BE AT THE POTENTIOMETER IN ORDER TO STABILIZE THE OUTPUT AT EXACTLY 0 VOLTS? +12 V +12 V V) Voltmeter 12 V 5V -12V...