design a bistable multivibrator using an op amp with+- 10v output saturation voltages L+=L-=8v and a...

Question

Question

design a bistable multivibrator using an op amp with+- 10v output saturation voltages L+=L-=8v and a hysteresis width of 160 mv

Answer 1

Answer #1

please upvote if it is helpful

Answer 2

Similar Homework Help Questions

Aufilo polasi For the op amp shown below, the output saturation voltages of the op amp...

Aufilo polasi For the op amp shown below, the output saturation voltages of the op amp shown below is t 10 volts. In addition, assume that conducting 6. ( 16 points) the a conducting diode has a voltage drop of 0.7 volts. Furthermore, R- R-10 KQ (a) Ir v1.SV, find and v (b) If v, =-2.5 V, find Vo and va
Use only passive components and exactly one op amp to design an astable multivibrator. It must have an output of a 30

Use only passive components and exactly one op amp to design an astable multivibrator. It must have an output of a 30
The output voltage of a particular op-amp increases 8V in 12 micro seconds in response to...

The output voltage of a particular op-amp increases 8V in 12 micro seconds in response to a step input voltage. The slew rate is ?

design an op amp comparator with the following characteristics v=10v, vd=0.7v and Rf=infinity

design an op amp comparator with the following characteristics v=10v, vd=0.7v and Rf=infinity
4. Using resistor values in the 1 kOto 100 ㏀ range, design an op amp circuit...

4. Using resistor values in the 1 kOto 100 ㏀ range, design an op amp circuit that has the following output voltage vout, where va, Vb, Ve and va are input voltages. Use as many op amps as you like
Using only one op-amp, design an amplifier that will have the following output:

Using only one op-amp, design an amplifier that will have the following output: Vo = 16 (Vi2 - Vi1)

3. Design an op amp circuit using one op amp that will take two inputs, Vi...

3. Design an op amp circuit using one op amp that will take two inputs, Vi and V2, and produce an output Vo--4V1 - 2V2.
(a) Design a inverting Schmitt trigger circuit to be used as a zero crossing detector with transition voltages about ±25...

(a) Design a inverting Schmitt trigger circuit to be used as a zero crossing detector with transition voltages about ±25 mV. Assume the saturation voltages for the op–amp are ±13 V. Draw the voltage transfer characteristic (VTC), i.e., vout vs. vin. (b) Design an astable multivibrator to produce a square signal with a frequency of 1 kHz using C=0.01 µF, R1 = 30 kΩ, and R2 = 20 kΩ. Sketch the circuit waveforms (vo, v +, and v −) assuming...
Learning Goal: To analyze op amps that sum different input voltages. Before proceeding, review summing op...

Learning Goal: To analyze op amps that sum different input voltages. Before proceeding, review summing op amp circuits and the ideal op amp assumptions. Figure 1 of 1 Review Part A - Calculating the output voltage of a summing op amp circuit For the circuit shown(Figure 1). determine V, when R1 = 3.4 kN, R2 = 5.0 kN. R3 = 7.0 kN Rp = 100 kn. Vi = 20 mV, V = 50 mV V3 = 280 mV and Voc...

i)draw the transafer charcheristics for this circuit? ii)Derive expressions for VTH and VTL? iii)Let L+ = - L- = 10 V, and R1=1 k Ω , choose R2 in order to get a hysteresis of 100mV width? iv).An engi...

i)draw the transafer charcheristics for this circuit? ii)Derive expressions for VTH and VTL? iii)Let L+ = - L- = 10 V, and R1=1 k Ω , choose R2 in order to get a hysteresis of 100mV width? iv).An engineer decided to modify the given circuit by disconnecting the inverting input of the op-amp from the ground and connecting it to a constant voltage source Vx. Derive expressions for VTH and VTL and Draw the transfer characteristics in this case.? Question...