QUESTION 1. (15 points) GIVEN THE INPUT WAVEFORMS, ASSUMING VOLTAGE VOur IDEAL OP AMP. DRAN THE OUTPUT IVEN THE INPUT WAVE A. DRAW THE OUTPUT VOLTAGE Voor ON TOP OF INPUT SIGNAL V +V B. DRAW THE...
Problem 2 110 points) For an ideal op-amp model and a typical 741 op-amp chip, the following partial table is provided. 1. Furnish the two (2) missing responses in the "Typical Value" column from the attached UM741 data sheet. Note: Use the "Typ" column on the data sheet for your responses. 2. Furnish the four (4) missing responses in the "Ideal Value” column from what you remember in class about the ideal op amp model Ideal Value Typical Value Parameter...
Q1. You are given a 12 V DC power supply. You are expected to develop a voltage divider to achieve a voltage of nominal 5V value using a pair of resistors from the E 12 range, with the restrition that you are not expected to draw a current of more than 1 mA from the 12 V DC supply i. Develop a simple circuit showing the possible values for each resistor pair, and the range of the DC output possible...
a. (10 pts) Implement the voltage amplifier shown below using an ideal op amp circuit. You have one op amp available for this circuit, and a range of resistors with values from 1 kΩ to 100 ka. Draw the schematic of your op amp circuit, labeling resistor values. Make sure the gain, input resistance, and output resistance of your circuit matches the model in the schematic. R=012 *100v, RL 100 b. (5 pts) Your amplifier circuit should have a frequency...
Assuming an ideal op-amp in the following circuit, find output voltage, Vo if R1= 2 KS, R2=8 KN, R3=3.4 KA, R4=6 KN, R5=20 KN, R6=2.9 KN, RL=12.5 KN, V1=1V, 12=0.5 mA and V3=3.1 V. R6 R1 R5 VO + RL 12 R2 V1 R3 { R4 w V3 Answer: "V
thanks Laboratory 1: operation amplifier characteristics A. Objectives: 1. To study the basic characteristics of an operational amplifier 2. To study the bias circuit of an operational amplifier B. Apparatus: 1. DC Power supply 2. Experimental board and corresponding components 3. Electronic calculator (prepared by students) 4. Digital camera (prepared by students for photo taking of the experimental results) 5. Laptop computer with the software PicoScope 6 and Microsoft Word installed. 6. PicoScope PC Oscilloscope and its accessories. 7. Multimeter...
Questions 4-20. Questions 4-20. QUESTION 4 the output becomes The longer a signal is applied to the input of an integrator op amp, the a smaller b. larger QUESTION 5 the output becomes. The faster the voltage applied to the input of a differentiator changes, the a smaller . b. larger QUESTION 6 voltage than for a negative-going signal. A Schmitt trigger switching threshold for a positive-going input signal is at a a lesser . b.greater QUESTION 7 If a...
Assuming an ideal op-amp in the following circuit, find output voltage, Vo if R1= 2 K2, R2=8 K2, R3=5.1 K2, R4=6 KN, R5=14 KN, R6=4.2 KS, RL=10.3 KS, V1=1V, 12=0.5 mA and V3=3.2 V. R6 R1 R5 Vo w + * RL + 12 R2 V1 R3 R4 V3 Answer: OV Using the above circuit, but consider the following component values: R1= 2 K12 R2=8 K2, R3=2.9 K2, R4=6 KI2, R5=10.8 K92, R6=15 KO, RL=10 K2, V1=1V, 12=0.5mA and V3=2V....
Assuming an ideal op-amp in the following circuit, find output voltage, Vo if R1= 2 K2, R2=8 K12, R3=3.8 KS2, R4=6 KI2, R5=15 KS2, R6=3.8 KN, RL=9.8 K12, V1=1V, 12=0.5 mA and V3=2.2 V. } R6 R1 w R5 w + Vo + } RL 12 R2 V1 R3 R4 + +1 V3 Using the above circuit, but consider the following component values: R1= 2 KN R2=8 K2, R3=4.1 K12, R4=6 KI2, R5=17.0 K12, R6=15 KI, RL=10 KI, V1=1V, 12=0.5mA...
Assuming an ideal op-amp in the following circuit, find output voltage, Vo if R1= 2 K12, R2=8 KN, R3=3.9 KN, R4=6 KN, R5=18 K2, R6=4.4 KN, RL=12.5 KN, V1=1V, 12=0.5 mA and V3=3.4 V. R6 R1 R5 Vo + + RL R2 V1 R3 R4 + V3 Answer: LOV Using the above circuit, but consider the following component values: R1= 2 KO2 R2=8 K12, R3=3.6 K12, R4=6 K12, R5=16.9 KN, R6=15 KN, RL=10 KO, V1=1V, 12=0.5mA and V3=2V. What is...
10. Draw below a schematic of an inverting op amp circuit operating from a single +voltage DC supply, that has a gain from input to output Av = 5 WITHOUT DISTORTION, with a 1kΩ load resistor. The input will be a 500mVRMS sinewave. BE SURE TO SHOW ALL POWER AND GROUND connections and POWER VOLTAGE LEVELS. Use Esupply = +20V, and assume 1 V headrooms.