Homework Answers
Add Answer to:
the resolution was solved in many ways.. could someone show me
how to solve
JU Renation...
A 4-bit Reduced-Resistance-Ratio D/A Converter, as shown in Figure 1, is used in an electronic system....
A 4-bit Reduced-Resistance-Ratio D/A Converter, as shown in Figure 1, is used in an electronic system. w 1 to 4R 4R XXX < M 3R (... Figure 1 A 4-bit Reduced-Resistance-Ratio D/A Converter You are asked to modify the circuit in Figure 1 to design a 6- bit Reduced-Resistance-Ratio D/A Converter for a new electronic system. (a) Draw a diagram to show the 6-bit Reduced-Resistance-Ratio D/A Converter. (10%) Analyse and justify the components required in the 6-bit converter and calculate...
1900) An analog input module uses an A/D converter with 8-bit resolution. The module range is...
1900) An analog input module uses an A/D converter with 8-bit resolution. The module range is -10 volts to +10 volts. Calculate the module output (digital count) when the input voltage is 3.7 volts. 1) floating point calculation, 2) discrete rounded result (actual digital count), 3) answer-2 minus answer-1 and 4) voltage resolution or smallest detectable change (volts). Assume the minimum digital value is zero. ans:4 thats all that was given to me
(a) We have an analogue to digital converter (ADC) described as 8 bit, with a 3V reference and 0V offset. What is the resolution, expressed in millivolts? [2] (b) For an input voltage of 0.6V, what i...
(a) We have an analogue to digital converter (ADC) described as
8 bit, with a 3V reference and 0V offset. What is the resolution,
expressed in millivolts? [2]
(b) For an input voltage of 0.6V, what is the digital output
value of the ADC described in (a)? Express your answer in both
binary and hexadecimal. [3]
(c) An industrial oven has a thermometer that outputs a voltage
from 0 to 1V for a corresponding range of temperatures of 0 to...
1. An A/D converter will convert voltages over a 0 to 10 V range. How many...
1. An A/D converter will convert voltages over a 0 to 10 V range. How many bits must it be to achieve a 1 mV resolution over the entire range? 2. You have an A/D converter that will convert over a range of 0 to 5 V. You input an analog signal to it that has a range of 1 to 3.5 V. What must be the number of bits of the converter to achieve a resolution of 1% of...
can you show me how did they solve this one? 4.1 Calculate the mean square output...
can you show me how did they solve this one?
4.1 Calculate the mean square output noise voltage when a signal generator with an output resistance of Copyrig 600 22 is connected to the input of the two-port network shown. 10 KS 10 k. Answer: 4.002 x 10-15v2.
Can someone help me design a gate level circuit and model using HDL? It needs to...
Can someone help me design a gate level circuit and model using HDL? It needs to convert 3-bit gray code to a binary number representation 2) adds the gray code input to its binary representation3) includes a flag(output)to determine when an overflow occurs. For example 111 in gray code is 5 in base 10, the binary representation for 5 is 101, the sum is 1100, an overflow has occurred and the overflow bit is set to 1. You will show...
Problem 6 (15 points): The general structure of an N -bit R-2R ladder digital to analog...
Problem 6 (15 points): The general structure of an N -bit R-2R ladder digital to analog converter (DAC) is shown below, where the voltages at each of the input pins are either 0 or 4 V (for binary "O" and "1", respectively). Assume N- 5. A stream of 5-bit unsigned integers, x[n], are applied to the input of this ladder in binary format (for example, if x13-12, which is B01100 in binary, then a2 and a3 are 4V while ao,...
Could someone please write worked solutions for part 2-5 of this question? Thank you Q3 (35...
Could
someone please write worked solutions for part 2-5 of this
question? Thank you
Q3 (35 marks) An accelerometer with a charge sensitivity of 83 pC/g and a capacitance of 1000pF is connected to a voltage follower with an input connector capacitance of 15pF (in parallel with the cable capacitance), a 10,000pF blocking capacitor and a 100M2 resistance. A 3m long cable with a capacitance of 312PF connects the accelerometer and the voltage follower. Determine 1) The schematic of the...
Hello, can someone show me how to do these homework questions step by step as soon...
Hello, can someone show me how to do these homework questions step
by step as soon as possible Thank you.
Question # 1 Calculate Z. Frequency is 100 K Hz. Calculate total current. a. b. 50Ω 100 m H Rt L 1 100220 R2 400 L 2 200 m H Question # 2 For the Network in figure 2. Frequency is 1 K Hz. a. Find Z b. Calculate total current (hotal) and current flowing through capacitor 100 m H)L1...
1) help me with this question. solution is posted. please help step by step of how...
1)
help me with this question. solution is posted. please
help step by step of how to get the solution.
2)
same with the above question also. solution posted.
please explain. just part b on the second question. Thanks
Bonus Problem 2(4 points):in the linear potentiometer shown below (which is intended to measure the displacement, x, in cm), assume E = 2 V. The resistive bar has length, L= 10 cm and a total resistance of 800 O. An additional...
A 4-bit Reduced-Resistance-Ratio D/A Converter, as shown in Figure 1, is used in an electronic system. w 1 to 4R 4R XXX < M 3R (... Figure 1 A 4-bit Reduced-Resistance-Ratio D/A Converter You are asked to modify the circuit in Figure 1 to design a 6- bit Reduced-Resistance-Ratio D/A Converter for a new electronic system. (a) Draw a diagram to show the 6-bit Reduced-Resistance-Ratio D/A Converter. (10%) Analyse and justify the components required in the 6-bit converter and calculate...
(a) We have an analogue to digital converter (ADC) described as
8 bit, with a 3V reference and 0V offset. What is the resolution,
expressed in millivolts? [2]
(b) For an input voltage of 0.6V, what is the digital output
value of the ADC described in (a)? Express your answer in both
binary and hexadecimal. [3]
(c) An industrial oven has a thermometer that outputs a voltage
from 0 to 1V for a corresponding range of temperatures of 0 to...
1. An A/D converter will convert voltages over a 0 to 10 V range. How many bits must it be to achieve a 1 mV resolution over the entire range? 2. You have an A/D converter that will convert over a range of 0 to 5 V. You input an analog signal to it that has a range of 1 to 3.5 V. What must be the number of bits of the converter to achieve a resolution of 1% of...
can you show me how did they solve this one?
4.1 Calculate the mean square output noise voltage when a signal generator with an output resistance of Copyrig 600 22 is connected to the input of the two-port network shown. 10 KS 10 k. Answer: 4.002 x 10-15v2.
Problem 6 (15 points): The general structure of an N -bit R-2R ladder digital to analog converter (DAC) is shown below, where the voltages at each of the input pins are either 0 or 4 V (for binary "O" and "1", respectively). Assume N- 5. A stream of 5-bit unsigned integers, x[n], are applied to the input of this ladder in binary format (for example, if x13-12, which is B01100 in binary, then a2 and a3 are 4V while ao,...
Could
someone please write worked solutions for part 2-5 of this
question? Thank you
Q3 (35 marks) An accelerometer with a charge sensitivity of 83 pC/g and a capacitance of 1000pF is connected to a voltage follower with an input connector capacitance of 15pF (in parallel with the cable capacitance), a 10,000pF blocking capacitor and a 100M2 resistance. A 3m long cable with a capacitance of 312PF connects the accelerometer and the voltage follower. Determine 1) The schematic of the...
Hello, can someone show me how to do these homework questions step
by step as soon as possible Thank you.
Question # 1 Calculate Z. Frequency is 100 K Hz. Calculate total current. a. b. 50Ω 100 m H Rt L 1 100220 R2 400 L 2 200 m H Question # 2 For the Network in figure 2. Frequency is 1 K Hz. a. Find Z b. Calculate total current (hotal) and current flowing through capacitor 100 m H)L1...
1)
help me with this question. solution is posted. please
help step by step of how to get the solution.
2)
same with the above question also. solution posted.
please explain. just part b on the second question. Thanks
Bonus Problem 2(4 points):in the linear potentiometer shown below (which is intended to measure the displacement, x, in cm), assume E = 2 V. The resistive bar has length, L= 10 cm and a total resistance of 800 O. An additional...
Most questions answered within 3 hours.
-
Rice Products in Bangladesh
Business behavior is derived in large part from the basic cultural
environment...
asked 25 minutes ago -
The following base sequence is found for a mRNA fragment from
wild-type E. coli: 5'- UAUCAGUAGAUAAUGUAACC-3'...
asked 48 minutes ago -
For this exercise, round all regression parameters to three
decimal places.
One of the two tables...
asked 1 hour ago -
What is the 5% level of significance for mean = 3.60, standard
deviation = 0.94, and...
asked 1 hour ago -
Prior to beginning work on this discussion, please read the
article by Hayley Peterson, 15 Companies...
asked 1 hour ago -
Which pair of aqueous solutions, when mixed, will form a
precipitate?
A) NaNO3 and AgC2H3O2
B)...
asked 1 hour ago -
1-Write an algorithm to get two numbers from the user (as
inputs) and calculate the sum...
asked 5 hours ago -
Define white-collar crime. What is the difference between
offender and offense-based definitions of white-collar crime? What...
asked 5 hours ago -
Consider a reaction which is 1st order with respect to A and 1st
order with respect...
asked 6 hours ago -
c++
The length of the hypotenuse of a right-angled triangle is the
square root of the...
asked 6 hours ago -
When a metal rod is heated, not only its resistance but also its
length and cross‐sectional...
asked 6 hours ago -
write a c++ program that computes the L^1 - Norm of a given
vector (L^1 norm...
asked 6 hours ago