ZuoTi.Pro
Question

An aluminum joint is clamped using an M8 x 1.25 class 10.9 fastener with rolled threads; the bolt was initially tightened to 80% of its proof load. Joint stiffness is twice that of the bolt. A cyclic external tensile service load that fluctuates between 0 and 5 kN is applied to the bolted joint system. bolt for infinite life, with 50% confidence level. The joint operates at room temperature. Determine the fatigue safety factor of the Hint: check also for bolt yield and joint separation under the cyclic ext on your results) ernal load, and comment
engineering   Mechanical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

8 mm nominest clio maky Single Sta Tensile Stness Artur At= 36.6 mm2- For Abkumtnium 6 11 von lons rtse lion

0 0
Add a comment
Know the answer?
Add Answer to:
An aluminum joint is clamped using an M8 x 1.25 class 10.9 fastener with rolled threads;...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • Ajoint is composed of a ¾ in.-16 UNF fastener (Steel Grade 5) with cut threads clamping...

    Ajoint is composed of a ¾ in.-16 UNF fastener (Steel Grade 5) with cut threads clamping 2 Aluminum plates. The clamped members are 5 times stiffer than the bolt. If the initial preload is 80% of the bolt's proof load, what is the service load that would cause joint separation? Assume that the extemal load is applied at the exact location of the bolt (bolt load factor n-I The fastener in the joint analyzed in Problem 1 is tightened to...

  • A ¾ in. UNF, grade 7 bolt with rolled threads is used in a joint having...

    A ¾ in. UNF, grade 7 bolt with rolled threads is used in a joint having a soft gasket for which the clamped member stiffness is only half the bolt stiffness. The initial bolt tightening corresponds to Fi= 16000d, where d is in inches and Fi in lbs. During operation, there is an external separating force that fluctuates between 0 and P. Assuming a design factor of safety of 2: a) Estimate the Maximum P that would not cause eventual...

  • [3]. (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates...

    [3]. (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line, determine the factor of safety guarding against fatigue failure for the...

  • 131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates...

    131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips. The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line, determine the factor of safety guarding against fatigue failure for the...

  • The material is steel. hence the ultimate strength can be found.

    the material is steel. hence the ultimate strength can be found. 131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips. The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line,...

  • For a bolted assembly with eight bolts, the stiffness of cach bolt is k 1.0 MN/mm...

    For a bolted assembly with eight bolts, the stiffness of cach bolt is k 1.0 MN/mm and the stiffness of the members is k26 MN/mm per bolt. The bolts are preloaded to 75 peroner of proof strength. Assume the external load is equally distrihuted to all the bolts. The bolts am M6 x1 class 5.8 with rolled threads. A fluctuating external load is applied to the cntire with P 60 kN and P - 20 kN. (a) Determine the yielding...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT