1. Discuss the basics of WLAN site survey.
Answer:
The ultimate goal of a wireless site survey is to determine the number and placement of access points (or mesh nodes) that provides adequate signal coverage throughout a facility or city area. With most implementations, “adequate coverage” means support of a minimum data rate or throughput. In order to perform a successful survey, you’ll need to relate the required performance to a value that survey tools measure, such as SNR. A wireless site survey also detects the presence of RF interference coming from other sources that could degrade the performance of the wireless LAN.
The need and complexity of a wireless site survey will vary depending on the facility. For example, a small three room office may not require a site survey. This scenario can probably get by with a single Wi-Fi access point (or router) located anywhere within the office and still maintain adequate coverage. If the access point encounters RF interference from another nearby wireless LAN, you can likely choose a different channel and eliminate the problem.
A larger facility, such as an office complex, airport, hospital, or warehouse, or an outdoor area like a city, generally requires an extensive wireless site survey. Without a survey, users will probably end up with inadequate coverage and suffer from low performance in some areas.
When conducting a wireless site survey, consider the following:
1. Understand the wireless requirements. In order to identify optimum locations for access points or mesh nodes, you must have a good understanding of specific requirements for the network that impacts signal coverage. For example, maximum range between a client device and the access point decreases as data rate and resulting performance increases. Thus, you need to know the target data rates (and throughput) to correctly interpret survey results. Also, client devices may have relatively low transmit power, which must be taken into consideration when using most site survey tools. Be sure to identify the technologies that the network will implement, such as 802.11g or 802.11n, and perform the survey with these technologies in mind.
2. Obtain a facility diagram. Before getting too far with the site survey, locate a set of building blueprints or city maps. If none are available, prepare a drawing that depicts the location of walls, walkways, etc. Site survey tools import diagrams in various image formats. Of course mapping software is a good source for outdoor city surveys. If all else fails for in-building surveys, consider taking a digital photograph of the fire escape diagram, which is usually present on hallway walls.
3. Visually inspect the facility. Walk through the facility before performing any testing to verify the accuracy of the facility diagram. This is a good time to note any potential attenuation barriers that may affect the propagation of RF signals. For example, a visual inspection will uncover obstacles to signals such as metal racks and partitions, items that blueprints generally don’t show. Also, note possible locations for mounting access points, such as above ceiling tiles or on pillars. For outdoor city environments, you should carefully assess the locations and availability of street lights and water towers for mounting mesh nodes and backhaul equipment. These actions will make the later testing efforts go much more smoothly.
4. Assess existing network infrastructure. Determine the capacity of any existing wired networks that can interface the access points or mesh nodes. Most buildings have Ethernet and in some cases optical fiber networks. Check on how much of the existing networks can be made available for supporting the wireless network. This will aid designers later on in the deployment when defining the architecture and bill of materials for the wireless network.
5. Identify coverage areas. On the facility diagram or city map, indicate all areas where coverage is needed, such as offices, hallways, stairwells, utility rooms, bathrooms, break rooms, patios, parking garages, and elevators. Also, identifying where users will not wireless coverage is important to avoid wasting time surveying unnecessary areas. Keep in mind that you might get by with fewer access points and lower equipment costs if you can limit the roaming areas.
6. Determine preliminary access point locations. By considering the location of wireless users and range estimations of the wireless LAN products you’re using, approximate the locations of access points that will provide adequate coverage throughout the user areas. Plan for some propagation overlap (generally 25 percent) among adjacent access points, but bear in mind that channel assignments for access points will need to be far enough apart to avoid inter-access point interference.
Be certain to consider mounting locations, which could be vertical posts or metal supports above ceiling tiles. Recognize suitable locations for installing the access point, antenna, and data / PoE cable. Also think about different antennas when deciding where to position access points. An access point mounted near an outside wall, for example, could be a good location if you use a patch antenna with relatively high gain oriented within the facility.
7. Verify access point locations. This is when the site survey testing begins. Most wireless LAN vendors provide wireless site survey software that identifies the associated access point, data rate, signal strength, and signal quality. You can load this software on a laptop and test the coverage of each preliminary access point location. Alternately, you can use a third party site survey tool available from several different companies, such as AirMagnet, Berkeley Varitronics Systems, and Ekahau.
Install an access point at each preliminary location, and monitor the site survey tool readings by walking varying distances away from the access point. There’s no need to connect the access point to the distribution system because the survey tests merely ping the access point or read the beacon signal strength. Very important: Definitely consider the SNR range boundary and uplink signal strength when interpreting the results. To make the access point easy to move about the facility, you can mount it on a pole attached to a cart with a battery and DC/AC converter. Otherwise, you’ll need to haul around an extension cord and always be looking for where to plug in for power (not recommended).
Take note of performance or signal readings at different points as you move to the outer bounds of the access point coverage. In a multi-floor facility, perform tests on the floor above and below the access point. Keep in mind that a poor signal quality reading could indicate that RF interference is affecting the wireless LAN. This would warrant the use of a spectrum analyzer to characterize the interference, especially if there are no other indications of its source. Based on the results of the testing, you might need to reconsider the location of some access points and redo testing for the affected locations.
8. Document findings. Once you’re satisfied that the location of access points you’ve identified will provide adequate signal coverage, document your findings on the facility diagrams by depicting the location of each access point. The installers will need this information.
These steps will point you in the right direction, but experience really pays off. If you’re new to wireless LANs, you’ll begin to build an odd intuition about the propagation of radio waves after accomplishing several wireless site survey
Discuss the basics methods for preparing an advertising budget.
What are the difference between WLAN and Cellular network? Name all available WLAN protocols in Data Networking i. What is CSMA/CA in WLAN and how it works? ii. Describe CSMA/CA technique that leverage DIFs, SIFs, and ACK. iii. Describe CSMA/CA that uses RTS and CTS frames b . Describe the wireless evolution steps starting from 2G to LTE ( 1 paragraph) c. What are the purposes of VLR and HLR in wireless network. What elements in mobile IP are similar...
Please discuss and explain the importance of intellectual property law. Please explain the basics of patent law, trademark protection, or copyright protection.
1. Cholesterol is not metabolized for energy. Discuss the roles of cholesterol, site of synthesis, and its turnover.
Case Project 7-1: Planning a Wireless Network Site Survey You are a network engineer for a small motel chain that has just been acquired by a large hotel company. The plan is to keep your company’s motels as a separate brand from the new parent company. The parent com- pany wants to upgrade the facilities in your motel chain, including the wired LANs. The company plans to implement WLANs both to assist in motel administration and to provide guests with...
Discuss the issues of integrity on wrong site surgery.
BUSINESS RESEARCH 1: Types of Research. Discuss and Explain with atleast minimum of five pages. Site the references.
According to a survey, only 15% of customers who visited the web site of a major retail store made a purchase. What is the probability that a random sample of 50 will have at least 30% of customers who will make a purchase after visiting the web site? a. 0.9985 b. 0.4984 c. 0.0016 d. 0.9984 e. 0.0015
7. Explain the basics of enzyme function and structure (sketch an enzyme and label the active site, allosteric site, where the substrate binds, where competitive and non-competitive inhibitors bind). Include how many different reactions can be catalyzed by an enzyme and how many times an enzyme can catalyze that reaction.
describe how enzymes act as biological catalysts that occurs at the active site. Discuss catalysis and competitive inhibition. how do each use the active site of the protein? what is an active site and why is it so inportant to biological catalysis.