2)Passive Filter: High Pass Filter Lab Experiment 3) Given the following RLC series circuit. V, =...
Learning Goal: To analyze and design a passive, second-order bandpass filter using a series RLC circuit. A bandpass filter is needed for an equalizer, a device that allows one to select the level of amplification of sounds within a specific frequency band while not affecting the sounds outside that band. The filter should block frequencies lower than 1.8 kHz and have a resonant frequency of 5.4 kHz A 3.2 AF capacitor and any needed resistors and inductors are available to...
Consider an RLC series circuit with R = 600 Ω, L = 3 H, C = 4μF, generator voltage V = 20 v, frequency= 60 hz. Find a) the inductive impedance XL, b) capacitive impedance Xc , c) Total impedance Z, d) Line current I , e) Voltage drops VR , VL, ,Vc f) combination voltage VRL , and VLc , g) phase angle φ , h) resonant frequency f0 , i) Power dissipated by circuit.
4. We want to design a tuner (actually a band pass filter) for an AM radio station whose frequency isf 700 kHz. The tuner must be able to detect the AM sidebands which are located at ±5 kHz (695 kHz and 705 kHz) from the central frequency. An easy way to achieve the above is to use a series RLC circuit and take VR for the output voltage. The resonant frequency of this circuit is that of the radio station....
3. For the circuit shown in Figure 1, + VR - R = 3k 494 ET V 4.7 uF E = 8V sin(20,000t +60° -VL + Z = ? m L = 0.5 H Figure 1 i. ii. iv. v. vi. vii. Find the total impedance Zr in polar form. Draw the impedance diagram Find the current and the voltages VR, Vi and Vc in phasor form. Draw the phasor diagram of the voltages E, VR, V., and Vc and...
(1 point) In an RLC series circuit, the rms potential difference provided by the source is V = 220 V, and the frequency is f = Hz. Given that L 0.35H, C = 45 pF, and VR = 75 V. find: 260 2 a) I (rms); A b) R; R 22 c) VL (rms); VL V d) Vc (rms). Vc V
An RLC series circuit has a resistance of R = 325.0 Ω, an inductance L = 0.3000 mH, and a capacitance C = 32.00 nF. (a) What is the resonant frequency? kHz (b) If the capacitor breaks down for peak voltages in excess of 7.000 × 102 V, what is the maximum source voltage amplitude when the circuit is operated at the resonant frequency? kV
please use multisim to answer all the parts. EXPERIMENT 3 TESTING SERIES & PARALLEL RESONANCES Objectives: To examine the conditions of resonances To observe the resonant circuit properties Equipment & components: A personal computer with Multisim software Preview questions: 1. How does the resonant frequency relate to the inductance and capacitance in a series LC circuit? 2. When the circuit in Figure 1 is tuned to resonant frequency, how does the voltage cross the resistor relate to the applied voltage?...
3.The phasor diagrams for a series RLC circuit are shown below. Rank the frequencies from lowest to highest. Which frequency is closest to the resonance? a. b. VI Vt Vc 4. Circuit / has a reonant frequency of wy, What is the resonant frequency wn of circuit // in terms of w? Circuit L Circuit IT 2L C/2 ε sin(40t) & sin(ot) 5. At time t -0 the capacitor in the circult below is fully charged with Qmax and the...
290 Hz. Given that (0 points) In an RLC series circuit, the rms potential difference provided by the source is V = 170 V, and the frequency is f L 0.2 H, C 30 uF, and VR = 20 V, find: a) I (rms); I A b) R; R= 12 c) VL (rms); VL = V d) Vc (rms). Vc = V
(1 point) In an RLC series circuit, the rms potential difference provided by the source is V = 190 V, and the frequency is f = -0 Hz. Given that L = 0.6 H, C = 75 uF, and VR = 20 V, find: a) I (rms); I = b) R; R= c) VL (rms); VL = d) Vc (rms). Vc =