Sove and draw Free body diagram please!
Sove and draw Free body diagram please! Promblem 3 m = 3Kg; l = 0.5m; b...
3. Draw a free body diagram for a mobile with a 3kg weight that is .8m from the pivot and a 5kg weight which is twice as far as the 3kg weight. Both of these weights are on one side of the pivot point and a 12kg weight is on the opposite side. Be sure to include magnitudes of forces.
Exercise 1: Draw a free body diagram for M. what does the tension turn out to be? please chose one: [1] Mg [2] mg [3] (M+m)g [4] (M-m)g Exercise 2: Draw a free body diagram for m. what does the mass ratio, m/M, turn out to be? please chose one: [1] cos [2] tan [3] sin [4] 1 Exercise 3: What is the radius of the circle in which m moves? Use the free body diagram for m to write...
Figure 1: 1) Please draw the free-body diagram of mass M in Figure 1(a). The diagram should include the pulling force F, gravitational force Mg, normal force N, and friction force fk. 2) Consider the graph in Figure 1(b). Please explain why the average of pulling force F in Region (ii) can be regarded as the kinetic friction force fx. (You may refer to the free body diagram in Question 1.) F个 (i) rest constant speed Force sensor h. 1)...
draw free body diagrams and answer questions please Draw the free body diagram for the bob (note that the spring is not attached at this time): bobt Equilibrium Marker 2. How does spinning the bob faster affect the period (time required for 1 full revolution)? The period increases. It takes more for the bob to go around once. The period stays the same. The period decreases. It takes less time for the bob to go around once. to the centripetal...
2. (a) Draw a free body diagram for member ABC shown below. (b) Determine the reactions at the supports A and C. P = 10 kN and a = 1 m. Begin your solution on this page 30
roblem #3 ( In the Diagram below, a rigid pipe is loaded and supported as shown. Supports at A, B, & C are Spherical Ball Bearings (don't resist moments). Pipe is considered weightless. Solve for the Reacations at A, B and C 450 N 0.4 m 0.4 m Problem #4 Draw the Free Body Diagram with all forces and reactions shown. Point A is supported by a Spherical Ball Bearing. Point c is a Cable. Point D is a ball...
For the shaft shown on the next page, draw the free body diagram of just the shaft (isolated from the pulleys) including directions and values of all reaction loads at the self-aligning bearings A and B. Once complete, directly under your FBD, draw the shear force diagram (SFD), bending moment diagram (BMD) and torque diagram (TD) for the shaft with all important values shown on the figures. Directions are critical and you must show your axes (choose). Note, in this...
Please draw the forces acting on the free body diagram if necessary and answer the question clearly. Thank you. the angular momentum of the system. Find Isys - L= Isys W (2.) A disk of mass M and radius 2R is free to rotate about an axis through the center of the disk. A small mass M is attached to the disk, a distance R from the center. If the disk is made to rotate with angular velocity o, find...
PLEASE DRAW FREE BODY DIAGRAM Problem 9/10 0.8 m 1.5 m-15 m Using the method of joints, determine the force in each member of the truss shown. Let P 30kN, Q-7KN, and R 8kN. Round the final answers to the nearest kN. Use positive values for tension and negative for compression. FAB FAD BD BE T FDE-
Please draw the forces acting on the free body diagram if necessary and answer the question clearly. Thank you. 4. A rod AB of mass M and length L is free to rotate about a horizontal axis through A. The rod is held horizontal and the endB is released. The rod rotates about A, and when it is vertical, the end B collides with a small mass M/2 and the mass gets attached to the rod. In the Sbsequent motion,...