11 Review Review Part A - Stress-concentration factor due to notches on the surface at point...
Review Part A A wood beam is reinforced with steel straps at its top and bottorm as shown in the figure below (Figure 1). Determine the maximum bending stress developed in the steel if the beam is subjected to a moment of M = 110 kN-m Take E = 10 GPa 200 GPa Express your answer to three significant figures and include appropriate units. Units Submit Request Answer Part B Determine the maximum bending stress developed in the wood. Express...
u Review Part B - Calculate the moment of inertia Learning Goal: To find the centroid and moment of inertia of an I-beam's cross section, and to use the flexure formula to find the stress at a point on the cross section due to an internal bending moment. Once the position of the centroid is known, the moment of inertia can be calculated. What is the moment of inertia of the section for bending around the z-axis? Express your answer...
Learning Goal: To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 55 mm and is subjected to the loading shown. Let a = 190 mm, b = 220 mm , c = 350 mm, d = 240 mm , and P = 4.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 b В...
Part A -Normal Strain at a Specified Point Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below The dia meter of the bar is d- 120 mm. A bending moment is applied that causes the neutral axis to become conca o up. What is the normal strain h Express your answer to three significant figures. View Available Hint(s) 20 mm from the bottom of the bar if the radius of curvature...
Part A - Moment about the x axis at A Learning Goal: To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 60 mm and is subjected to the loading shown. Let a = 200 mm, b = 220 mm c = 340 mm, d = 230 mm, and P = 4.0 kN. Take point A to be at the top of the circular cross-section. (Figure...
Review Learning Goal: To use the superposition principle to find the state of stress on a beam under multiple loadings The beam shown below is subjected to a horizontal force P via the rope wound around the pulley. The state of stress at point A is to be determined. Part A - Support Reactions and Internal Loading Determine the support reactions Cy and Cz and the internal normal force, shear force, and moment on the cross-section containing point A. Express...
(A) Smin 100 mm Problem 1 (20 pts): Stress Concentrations Consider the flat bar with shoulder joints shown in Fig. A which is subjected to a tensile force P = 58 kN. The bar is made of Aluminum 6061 having maximum tensile strength Omax = 290 MPa. NOTE: plots of stress concentration factors for different types of loading can be found on page 6 (a) Determine the radius r [mm] for the fillets. (b) An identical flat bar shown in...
Learning Goal: To calculate the normal and shear stresses at a point on the cross section of a column. The state of stress at a point is a description of the normal and shear stresses at that point. The normal stresses are generally due to both internal normal force and internal bending moment. The net result can be obtained using the principle of superposition as long as the deflections remain small and the response is elastic. Figure < 1 of...
Review Part A -Normal strain in the x direction Learning Goal Determine the normal strain in the xdirection, r To determine the elongations and contractions in a rectangular prismatic member that is subjected to stresses in the x and y directions. Express your answer in inches per inch to three significant figures View Available Hint(s) The member shown is subjected to a compressive stress in the x direction of σε 375 ksi and a compressive stress in the y direction...
(A) 8 mm 100 mm Problem 1 (20 pts): Stress Concentrations Consider the flat bar with shoulder joints shown in Fig. A which is subjected to a tensile force P = 58 kN. The bar is made of Aluminum 6061 having maximum tensile strength Omax = 290 MPa. NOTE: plots of stress concentration factors for different types of loading can be found on page 6. (a) Determine the radius r [mm] for the fillets. (b) An identical flat bar shown...