Glassing is designed for the following attacks.
1. Force attack or Physical attack
2. Ballistic attack (Blast or Explosive attack)
3. Chemical attack
4. Thermal attack
As per UFC 3-340-02 the
Peak blast pressure for the a/b= 1 and 12 inch pane dimension
For the 3 msec blast pressure
= 50PSI
What are the types of attacks a glazing is designed for? Given a 12 inch thick...
15. What are the types of attacks a glazing is designed for? Given a 12 inch thick tempered glass of size 12 in x 12 in, what is the maximum blast pressure (in psi) that it can withstand given that the duration of the load is 10 ms. (5 points)
A simply supported one-way slab of 12 ft span and 8-inch thick is given. The rebar used in the slab is #8 at 6 inches on center. Determine how much live load (psf) may the slab safely carry. (f'c=3,000 psi, fy=40,000 psi).
A braced frame steel building is to be designed to resist blast
loads. The building is assumed to be at “medium” risk of a placed
bomb. Individual members in the building are to be analyzed as
separate one degree-of-freedom systems. Consider a W14x34 steel
column having a yield strength of 50 ksi. The building floors are
12 feet between story levels. The column is pinned at both ends.
The column supports exterior cladding; the bays are 24 feet on
center.See...
Design a square single column footing to support an 18 inch square interior column reinforced with 8-#10 bars. The column carries an unfactored dead load of 245 Kips that includes weight of soil and weight of footing and an unfactored live load of 20 feet below finished grade. The footing is 10 feet by 10 feet and is 30 inches thick. The allowable soil pressure is 5000 psf, fe' 4000 psi and fy 60000 psi. Concrete used shall be sand...
5. A holding fixture for a work piece 1.5 inch thick at clamp location is being designed. The detail of one of the clamps is shown in the figure. The spring is required to drive the clamp upward while removing or inserting a work piece. A clamping force of 10 lbf is satisfactory. The base plate is 5/8 inch thick. The clamp screw has a 7/16 in-20 UNF thread. Allow 0.05 inch diametral clearance between screw and the inner coil...
Given that Peak side-on overpressure = 17 psi; time of duration = 0.06 sec 70 feet 95 feet 15 feet Blast Calculate: 1. The shock front velocity (4 points) 2. The length of pressure wave (4 points) 3. The peak dynamic wind pressure. (4 points) 4. What expected physical injury can be anticipated per the UFC 3-340 (2 points)
11. Given that Peak side-on overpressure = 17 psi; time of duration = 0.06 sec 95 feet 70 feet 15 feet Blast Calculate: 1. The shock front velocity (4 points) 2. The length of pressure wave (4 points) 3. The peak dynamic wind pressure. (4 points) 4. What expected physical injury can be anticipated per the UFC 3-340 (2 points)
The walls are 10 in. thick with an allowable compressive stress of 300 psi (pounds per square inch). A 3 ft wide vertical strip of wall currently supports both a roof load of 1.5 kips and 11 floor loads of 2.0 kips per floor. Each story is 12 ft tall from floor to floor. The density of the masonry wall is 130 pcf (pounds per cubic foot). What is the maximum total force support by a 3ft wall segment for...
A 5" diameter abrasive cutoff wheel 1/16 in thick, and has a 1/2-in bore. It weighs 10 oz and is designed to run at 15 000 RPM. If the material is isotropic and v=0.25, find the maximum shear stress at the design speed. 1. 2. A cylindrical pressure vessel has an outside diameter of 9" and a wall thickness of 0.25". If the internal pressure is 470 psi, what is the maximum shear stress? If a torque of 75 in-lbs...
Kıc = Yovta A part has been designed in the form of a thick steel plate to support a load in tension. The design stress on the part is 1200 MPa. While in service the part will be routinely inspected with an X-ray non-destructive testing device. This X-ray inspection device will detect any interior cracks larger than 0.5mm. During the initial design of the part, the required Klc for the steel was determined to be 38MPa.m .5. This Kic value...