Consider the following drive train. Gears are shown by their pitch diameters. Gear 2 is the...
For a pair of spur gears with a diametral pitch of 12, and a 20° degree pressure angle and with the number of teeth on the pinion 11 and the number of teeth on the gear 18, compute all the features of the gear teeth described below: (a) Pitch diameter for the gear, (b) Pitch diameter for the pinion (c) The circular pitch, (d) Addendum, (e) Dedendum, (f) Clearance, (g) Whole depth, (h) The tooth thickness (hint: based on circular...
In the gear train shown below, the pinion 2 is the driver, and gear 5 is the output gear. All gears are spur gears has a module of 2.5mm and pressure angle of 200. The number of gear teeth are: N2 - 14, N3 - 84, N4 - 14, N5 - 70 teeth. The gear set transmits the power of 1.5KW at a constant angular velocity of XX rev/min. Where XX is the last two digits of your University ID...
A compound gear train is to be designed as a speed increaser to provide a total increase of speed by 30 to 1 ( 1 %). Use spur gears with a 20° pressure angle and a diametral pitch of 7 teeth/in. Assume same diametral pitch in both stages. 5 1) Specify appropriate numbers of teeth to minimize the gearbox size while avoiding the interference problem in the teeth. Use full-depth teeth Determine the gearbox outside dimension Y, assuming the wall...
2. Consider the triple speed reduction gear box shown in Figure 1. All the gears are made with a diametral pitch of 16 in. The input of the gear train is gear A, and the output is gear G. The gear train transmits an input toque of 250 lb-in, at a speed of 2,500 rpm clockwise. The number of teeth on each gear is given as follows: NA 24 teeth, Na = 60 teeth, Nc 20 teeth, No 58 teeth,...
A pair of helical gears is used with the following properties: 14.5 degree normal pressure angle, 45 degree helix angle, diametral pitch of 8 teeth/in, 1.5-in face width, and normal diametral pitch of 11.31 teeth/in. The pinion has 12 teeth and a 1.5in pitch diameter, and the gear has 32 teeth and a 4.0 in pitch diameter. Both gears have full-depth teeth. If a right-hand pinion and a left hand gear are placed in mesh, find the transverse contact ratio,...
estion- a) Find the speed ratio of the gear train shown in figure. What will be the direction of gear 7 b) Determine pitch line velocity (v r.w) of gear &, provided for gear 6 Imodule (D/T) 5mm e) If double the speed ratio (as calculated in a) is required with a simple gear train (having only two gears) number of teeth on driven gear, provided input gear has 20 teeth. IST IST 25T 33T I8T An epicyclic gear train...
A pair of straight bevel gears are mounted on shafts that are 90 degrees apart, and pinion transmits 10 hp at 300 rpm. The pinion has 6" outside pitch diameter, 2" face width, 20 teeth and Φ = 20˚. For a velocity ratio of 0.5, draw a free body diagram of gears showing all forces. What is torque produced about gear axis? The average pinion pitch diameter is 5.104"
Homework 6: The figure below shows a gear train where gear 1, on shaft a (input shaft), drives gear 2 with 32 teeth (denoted 32T) on shaft b, gear 3 (20T) also is on shaft b and drives gear 4 (507) on shaft c (output shaft). The pitch diameter of gears 1 and 2 are d = 24 mm and d = 48 mm. The center distance between gears 3 and 4 (distance between shafts b and c is 70mm....
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. a) What are the diameters of Gears 1, 2, 3, and 4? b) What is the pitch-line velocity of Gear 1, in ft/min? c) Is the pitch-line velocity of Gear 2 the same as Gear 1? d) What is the pitch-line velocity of Gear 3 (and, therefore, Gear...
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. Part 1. Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. Part 2. If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in, and allowable...