Homework Answers
Add Answer to:
estion- a) Find the speed ratio of the gear train shown in figure. What will be...
A compound epicyclic gear train is shown in the Figure. The shaft P is driven at...
A compound epicyclic gear train is shown in the Figure. The
shaft P is driven at 2500 rpm in the clockwise direction by a motor
of power rating 8 kW. The sun S2 is fixed. The number of teeth in
the gears are S1, 34; S2, 21; A1, 86 and A2, 73. Determine
The magnitude and direction of the angular velocity of the
shaft Q and
The torque required to fix the sun, S2
A, Q P S, 5,
Part 1 A simple epicyclic gear has a sun gear with 10 teeth and a ring...
Part 1 A simple epicyclic gear has a sun gear with 10 teeth and a ring gear with 100 teeth. If the sun gear is held stationary, calculate the speed/gear ratio when the ring gear is the input and the planet carrier is the output? Part 2 Two parallel shafts which are 220mm apart are to be connected by a simple gear train, will all gear centres on the same line, using gears from a pool of six gears of...
A compound epicyclic gear train is shown in the Figure. The shaft P is driven a...
A compound epicyclic gear train is shown in the Figure. The
shaft P is driven a 4000 rpm in the clockwise direction by a motor
of power rating of 10W . The annulus A2 is fixed. The
number of teeth in the gears are , S1,28;
S2,21; A1,72 and A2,99 .
Determine:
The magnitude and direction of the angular velocity of the
shaft Q
The torque required to fix the annulus, A2
A, A₂ P, P2 P P. z S
Problem 1 (50 points The planetary gear train shown in the figure uses spur gears with...
Problem 1 (50 points The planetary gear train shown in the figure uses spur gears with standard, involute teeth cut with a 20° pressure angle and a diametral pitch of 10 teeth/inch. Note that the contact between the gears is indicated by the pitch circles in the figure. a) Gear #2 has 18 teeth and gear #5 has 42 teeth. How many teeth must be on gear #4? b) If the arm (#3) is driven at 600 revolutions per minute...
** Not Multiple Choice Section ** 11. [25 points] Consider the planetary gear train shown in...
** Not Multiple Choice Section ** 11. [25 points] Consider the planetary gear train shown in the figure. * Gear E is the driver running at +100 rpm. The Arm (link A) is the output driven link. The ring gear B is fixed. The number of teeth given as: are NE 34 ND 17 Nc 26 a) Determine the number of teeth for the ring gear B. All gears use the same pitch b) Determine the rpm and the direction...
If, in the epicyclic gear train shown in Fig 4. .gear A rotates at 1000rev/min clockwise,...
If, in the epicyclic gear train shown in Fig 4. .gear A rotates at 1000rev/min clockwise, while E rotates at 500 rev/min anticlockwise, determine the speed and direction of rotation of the annulus D, and of the shaft F. All gears are of the same pitch, and the number of teeth in A is 30, in B is 20 and in E is 80. (U. Lond.) (Answer: 372 rev/min anticlockwise; 40rev/min clockwise) Fio. A
2. Fig.2 shows an epicyclic gear train in which the internal teeth on the gears A and B have the same diametral p...
2. Fig.2 shows an epicyclic gear train in which the internal teeth on the gears A and B have the same diametral pitch. Gear A has 88 teeth and gear B has 100 teeth both internally and externally. The sun-wheel C which is keyed to shaft P has 44 teeth and the pinion E keyed to shaft R has 25. There are floating compound planet wheels F, G. The power input to shaft R is 8 kW at 1440 rev/min....
A compound reverted spur gear train is to be designed to reduce the speed of a...
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in,...
A compound reverted spur gear train is to be designed to reduce the speed of a...
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in,...
A compound reverted spur gear train is to be designed to reduce the speed of a...
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. Part 1. Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. Part 2. If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in, and allowable...
A compound epicyclic gear train is shown in the Figure. The
shaft P is driven at 2500 rpm in the clockwise direction by a motor
of power rating 8 kW. The sun S2 is fixed. The number of teeth in
the gears are S1, 34; S2, 21; A1, 86 and A2, 73. Determine
The magnitude and direction of the angular velocity of the
shaft Q and
The torque required to fix the sun, S2
A, Q P S, 5,
A compound epicyclic gear train is shown in the Figure. The
shaft P is driven a 4000 rpm in the clockwise direction by a motor
of power rating of 10W . The annulus A2 is fixed. The
number of teeth in the gears are , S1,28;
S2,21; A1,72 and A2,99 .
Determine:
The magnitude and direction of the angular velocity of the
shaft Q
The torque required to fix the annulus, A2
A, A₂ P, P2 P P. z S
Problem 1 (50 points The planetary gear train shown in the figure uses spur gears with standard, involute teeth cut with a 20° pressure angle and a diametral pitch of 10 teeth/inch. Note that the contact between the gears is indicated by the pitch circles in the figure. a) Gear #2 has 18 teeth and gear #5 has 42 teeth. How many teeth must be on gear #4? b) If the arm (#3) is driven at 600 revolutions per minute...
** Not Multiple Choice Section ** 11. [25 points] Consider the planetary gear train shown in the figure. * Gear E is the driver running at +100 rpm. The Arm (link A) is the output driven link. The ring gear B is fixed. The number of teeth given as: are NE 34 ND 17 Nc 26 a) Determine the number of teeth for the ring gear B. All gears use the same pitch b) Determine the rpm and the direction...
If, in the epicyclic gear train shown in Fig 4. .gear A rotates at 1000rev/min clockwise, while E rotates at 500 rev/min anticlockwise, determine the speed and direction of rotation of the annulus D, and of the shaft F. All gears are of the same pitch, and the number of teeth in A is 30, in B is 20 and in E is 80. (U. Lond.) (Answer: 372 rev/min anticlockwise; 40rev/min clockwise) Fio. A
2. Fig.2 shows an epicyclic gear train in which the internal teeth on the gears A and B have the same diametral pitch. Gear A has 88 teeth and gear B has 100 teeth both internally and externally. The sun-wheel C which is keyed to shaft P has 44 teeth and the pinion E keyed to shaft R has 25. There are floating compound planet wheels F, G. The power input to shaft R is 8 kW at 1440 rev/min....
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in,...
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in,...
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. Part 1. Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. Part 2. If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in, and allowable...
Most questions answered within 3 hours.
-
A women tries to swim perpendicular across the river to the
opposite bank at 2.0m/s with...
asked 9 minutes ago -
The amount of time it takes for a student to complete a
statistics quiz is uniformly...
asked 1 hour ago -
True or False: If some system undergoes a reversible,
isothermal
process, then its entropy must remain...
asked 45 minutes ago -
You are analyzing the after-tax cost of debt for a firm. You
know that the firm’s...
asked 43 minutes ago -
You
are dining with a friend and use the friend's spoon to taste her
food, if...
asked 1 hour ago -
explain why The elasticity of demand for labor is higher the
higher the elasticity of supply...
asked 1 hour ago -
Hi just need to know if these statements are true or false and
why!!!
1. Magnetic...
asked 1 hour ago -
A radar transmits a pulse every 0.5
ms. It transmits an up-chirp of the duration of...
asked 1 hour ago -
Poehling Medical Center has a single operating room that is used
by local physicians to perform...
asked 1 hour ago -
Can somebody solve this? Insert 22, 78, 10, 56, 12, 7, 34, 56
into the Min-...
asked 1 hour ago -
Need a recent news article that was published less than 3 months
ago that talks about...
asked 1 hour ago -
Problem 2:
Composite and multi-valued attributes can be nested to any
number of levels. Suppose we...
asked 1 hour ago