A pipe system carries water from a reservoir and discharges it as a free jet, as...

Question

Question

A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made fr

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

501) 16 coe 1) coe assume can fluid model ideal then neglect friction minor losses losses and in flow we Know bernoulis Equa V 3om. CS Scanned with CamScanner

Add a comment

Answer 2

Similar Homework Help Questions

A pipe system carries water from a reservoir and discharges it as a free jet, as...

A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı=0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VÃ Pa = Pamb + y(30 m) р 2 and draw on the diagram the streamline you used. 2)...
A pipe system carries water from a reservoir and discharges it as a free jet, as...

A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı=0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VÃ Pa = Pamb + y(30 m) р 2 and draw on the diagram the streamline you used. 2)...
A pipe system carries water from a reservoir and discharges it as a free jet, as...

A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı= 0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is Vå Pa = Pamb + y(30 m) - p. 2 and draw on the diagram the streamline you...

3. (20 pts) Chapter 8 Viscous Flow in Pipes A pipe system carries water from a...

3. (20 pts) Chapter 8 Viscous Flow in Pipes A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200 mm diameter commercial steel pipe with two 90 deg elbows with K=0.4m and an inlet minor loss Ki-0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is V PA = Pamb + y(30 m) - P2 and draw...
PA = Pamb + y(30 m) - 2 3.(20 pts) Chapter 8 Viscous Flow in Pipes...

PA = Pamb + y(30 m) - 2 3.(20 pts) Chapter 8 Viscous Flow in Pipes A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kz=0.4m and an inlet minor loss K = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is va and draw...
A centrifugal pump is used to pump water at 77ºF from a reservoir whose surface is 20 ft above th...

A centrifugal pump is used to pump water at 77ºF from a reservoir whose surface is 20 ft above the centerline of the pump inlet. The Pipe System consists of 67.5 ft of PVC pipe with a 1.2 in ID and negligible average internal roughness height. The length of the pipe from the bottom of the lower tank to the pump inlet is 12 ft. There are several minor losses in the pipe: an acute edge entry (KL = 0.5),...

The system shown in the diagram consists of 1200m of cast-iron pipe with an internal diameter...

The system shown in the diagram consists of 1200m of cast-iron pipe with an internal diameter of 5cm (roughness of 0.00015 ft), two 45o and four 90o long radius elbows, a fully open bevel seat globe valve, and a sharp exit into a reservoir. If the elevation difference between the inlet and level in the reservoir is 10m, what gauge pressure is required at point 1 to deliver 0.005m^3/s of water at 20oC into the reservoir (use density of 998.2...
1. Water is pumped from a low reservoir to a high reservoir that is 20 m...

1. Water is pumped from a low reservoir to a high reservoir that is 20 m higher in elevation. The water is flowing at 1.5 m/s through a 305 mm internal diameter piping system. The water is at 18 degrees C. There are 1,000 m of piping, six standard 45 degree bends, two standard 90 degree bends, a branch flow tee, three gate valves, a swing check valve, a square inlet and a square outlet. The piping and valves are...
Problem 1: In the reservoir-pipe system below, water is supplied from reservoir A to reservoir B...

Problem 1: In the reservoir-pipe system below, water is supplied from reservoir A to reservoir B with a flowrate of 50 L/S. In the system, a pump with an efficiency value of n=0.70 is used. Length of the pipeline is L=5000m, pipe diameter is D=200 mm and the elevation difference between reservoirs is 40 m. According to this, a) Determine the required pump head (Hp). b) Find the required nominal pump power. c) Draw the relative energy grade line of...

this is all of the information given Problem 3. A piping system consists of 1200 m...

this is all of the information given Problem 3. A piping system consists of 1200 m of 5 cm diameter cast-iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp submerged exit into a reservoir. The elevation of the outlet relative to the inlet is 100 m. What gage pressure is required at the inlet to deliver 0.005 m2/s of water at 20°C into the reservoir? Assume that the density and...

A pipe system carries water from a reservoir and discharges it as a free jet, as...

Homework Answers