3. (20 pts) Chapter 8 Viscous Flow in Pipes A pipe system carries water from a...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı=0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VÃ Pa = Pamb + y(30 m) р 2 and draw on the diagram the streamline you used. 2)...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı=0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VÃ Pa = Pamb + y(30 m) р 2 and draw on the diagram the streamline you used. 2)...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı= 0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is Vå Pa = Pamb + y(30 m) - p. 2 and draw on the diagram the streamline you...
PA = Pamb + y(30 m) - 2 3.(20 pts) Chapter 8 Viscous Flow in Pipes A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kz=0.4m and an inlet minor loss K = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is va and draw...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with K -0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VA PA = Pamb +(30 m) - and draw on the diagram the streamline you used. TOT
) 25 points - Water flows in a piping system a section of which is shown below.Pipe is 30 mm ID commercial steel pipe. Velocity of flow is 1.6 m/s and is constant throughout. Pressure at Pt is 200 kPa. All the valves are fully open gate valves, all the elbows are regular 90° threaded. For water, p:1000 kg/m3, 0.00108 N-s/m2. Other necessary data is given on the diagram. Assume the flow is incompressible and steady. Determine the volume flow...
Water (p=998kg/m^3, u=0.001Pa*s) flows from reservoir A to reservoir B through the piping system shown. Each elbow has a minor loss coefficient of 1.2. Each valve has a minor loss coefficient of 3.2. The entrance and exit are both sharp edged. Determine the flow rate L/min. You now need to modify the piping system to increase the flow rate to 100L/min by reducing the length of the 25mm pipe. What must new length of the 25mm pipe be? 86. Water...
A flow rate meter is used to measure the flow rate of a water flow from left to right) in an inclined position. Due to spatial confinement, the two pressure taps-manometer tubes were inclined as well as shown. The meter is similar to a Venturi meter except at the small pipe the pressure tap is a stagnation pressure tap at 2. For the given geometries, calculate: 1) (4 pts)The velocity at the large pipe, in m/s 2) (3 pts)The velocity...
3 - (50 pts.) A fluid flow in a circular pipe is heated with a constant surface temperature. The pipe diameter is set to D (in m) and the length of the pipe to L -2.5m. The inlet temperature is 300 K and the inlet velocity is uniform. Use the following air properties: p=1 kg/m', u=2x10* Pa-s, k=0.03 W/m-K. The Reynolds number to Rep - 200 and the Prandt number to Pr=1.75. A section of the pipe is heated with...
Please solve a,b,c,d,e,f 1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...