in this question we have to find the discharge through pipe
PA = Pamb + y(30 m) - 2 3.(20 pts) Chapter 8 Viscous Flow in Pipes...
3. (20 pts) Chapter 8 Viscous Flow in Pipes A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200 mm diameter commercial steel pipe with two 90 deg elbows with K=0.4m and an inlet minor loss Ki-0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is V PA = Pamb + y(30 m) - P2 and draw...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı=0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VÃ Pa = Pamb + y(30 m) р 2 and draw on the diagram the streamline you used. 2)...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı=0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VÃ Pa = Pamb + y(30 m) р 2 and draw on the diagram the streamline you used. 2)...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı= 0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is Vå Pa = Pamb + y(30 m) - p. 2 and draw on the diagram the streamline you...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with K -0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VA PA = Pamb +(30 m) - and draw on the diagram the streamline you used. TOT
DON’T disregard the thermal conductivity of the pipe 3.) Oil at 200 C flows in a pipeline. The pipe has a 30-cm diameter and the flow is at an average velocity of 2 m/s. A 200-m-long section of the pipeline passes through icy waters of a lake at 0° C. The pipe is uncoated carbon steel with a thermal conductivity of 61 W/m o C. Determine (a) the temperature of the oil when the pipe leaves the lake, (b) the...
Prob em 1 pts in Lab 03 water friction, for the dark blue circuit the head loss h h1-h2 across bend "C" at 30% and 40% flow are recorded in the table 3 I below. The actual flow rates, Reynolds number, Blasius friction factor, and required water and pipe properties are included in the table. From the given information, complete cells L16, M10, M12, M16, NI0, N12,NI6,010, 012 and O16 in table 3.1 and determine the average minor loss coefficient...
Prob em 1 pts in Lab 03 water friction, for the dark blue circuit the head loss h h1-h2 across bend "C" at 30% and 40% flow are recorded in the table 3 I below. The actual flow rates, Reynolds number, Blasius friction factor, and required water and pipe properties are included in the table. From the given information, complete cells L16, M10, M12, M16, NI0, N12,NI6,010, 012 and O16 in table 3.1 and determine the average minor loss coefficient...
Question 2 4 pts Question 1lb) If viscous effects are negligible, determine the flow rate Qt (m3/s) at Point 1 in the large pipe if h-5.8 m and V2 66m/s The density of water is 1000 kg/m3. Atmospheric pressure Patm 101.325 kPa. Gravitational acceleration g- 9.81 m/s Your answer should be in m3/s and accurate to4d.р. Question 3 3 pts If viscous effects are negligible, determine the gauge pressure p1 (kPa) at Point 1 in the large pipe for Q1...
CENTRE INDEX NUMBER SECTION B 30 marks] Calculate the discharge through a pipe of diameter 200 mm when the difference of pressure head between the ends of the pipe 500 m apart is 4 m of water. Take the value off= 0.009 in the formula hl= a) 19.5e/s b)2.0es e)03 m's d) 29.3 e/s 2. A scale 1:50 scale model of ship is towed through sea water at a speed of 1 ms. A force of 2 N is required...