consider a negative unity feedback system whose feedforward transfer function is: (s) + 1/[(s+0.11(s+1)(s+10)] Braw a...
consider a negative unity feedback system whose feedforward transfer function is: (s) - 1/((s+0.11(s+1)(s+10) Brawa Bode plot of the open loop transfer function that includes an asymptotic and approximate estimate for both magnitude and phase. Answer he following questions Asymptotic phase lag at 1 rad/sec is _ degrees 0 -45 -90 0-135 -180 225 270 325 -360 Asymptotic phase lag at 10 rad/sec is _ degrees 0 -45 -90 0 -135 -180 -225 -270 360 none of these Asymptotic phase...
Low frequency DC gain is db 0 10 O 100 none of these Question 2 Low frequency DC phase lag is __ degrees OO O-90 O-180 O -270 O-360 none of these Question 3 Asymptotic magnitude slope at 5 rad/sec is __db/decade O 0 -20 O-40 O -60 O -80 - 100 none of these Question 4 Asymptotic magnitude slope at 50 rad/sec is _ db/decade -20 -40 -60 -80 O - 100 none of these
Consider the following magnitude and phase plot of a minimum phase system. Please answer the following and explain. Consider the following magnitude and phase plot of a minimum phase system. Is this system stable or unstable? Explain your answer. Bode Diagram: Minimum-Phase Systenm 100 Gain Crossover 40 -60 80 100 90 135 -180 225 -270 -360 Phase Crossover Op Og Frequency (rad/sec) Consider the following magnitude and phase plot of a minimum phase system. Is this system stable or unstable?...
5. Consider the feedback system in Figure 4 where! G(s) = 26+10% Figure 4 The Bode plot of G is shown in Figure 5. Boda Diagram Magnitude (dB) -100- -156 -135 -root -225 10 Frequency radici Figure 5: Bode plot of G (a) [2 marks] Find the phase margin, gain margin and gain crossover frequency (approximate as needed) for the case when C(s) = 1. PM = GM = wc = You are asked to design a feedback controller C(s)...
The values for y axes for the first graph on the top is the same as second graph on the bottom. Figure 1 shows the Bode diagrams for a particular system. a.) Sketch the polar diagram for this system, accurately indicating the location and numerical values for the phase and gain margins. The phase margin should be given in degrees, and the gain margin in actual units (i.e. not dB). Use arrows to indicate the di . rection of increasing...
The Bode plots for a plant, G(s), used in a unity feedback system are shown in Figure P10.7. Do the following: Find the gain margin, phase margin, zero dB frequency, 180° frequency, and the closed-loop bandwidth. Use your results in Part a to estimate the damping ratio, percent overshoot, settling time, and peak time. ANSWERS GIVEN BY PROFESSOR 1. Gain margin = 20dB, Phase margin = 55 deg, Zero dB frequency = 1rad/s, 180deg frequency = 4.5rad/s, bandwidth (-7dB) closed-loop...
6) The open loop transfer function of a control system is 10-011. Ata frequency of 1 Hz, the system phase shift is: (1) 0.9 kg (2) 5.7" tag (3) 18 (6) 36"lag (5) none of the above h) The open-loop transfer function of control system is 10 At high frequencies, the gain will: (1) be constant (2) roll off at -20 d/decade (3) roll off at -40 dB/decade (6) roll off at 60 dB/decade The open-loop transfer function of a...
6. Quiz W/Th: Consider the system G()(s 40) (s +4) s S- (a) Fill out the table below with the information you would need to sketch the Bode plot of G(s) Break Freq (rad/s) Type (# of LHP/RHP poles/zeros) Magnitude SlopePhase Slope (deg/dec) Term (dB/dec) (b) Calculate the magnitude (in dB) at 0.1 rad/sec and phase (in degrees) at 4 rad/sec (c) Determine which of the following Bode plots is correct for G(s). For full credit, provide enough explanation to...
The Bode diagram of the forward-nath transfer function of a unity-feedback control system is obtained experimentally when the forward gain Kis set at its nominal valuc. (a) Find the gain and phase margins of the system from the diagram as best you can read them. Find the gain- and phase-crossover frequencies. (b) Repeat part (a) if the gain is doubled from its nominal value. (c) Repeat part (a) if the gain is 10 times its nominal value. (d) Find out...
Consider the system given below where K is a constant gain, Gp is the plant, and Ge is a compensator. The Bode Plots of a Gp is given below. Problem 1: Bode Diagram 20 2 40 -60 80 -100 90 135 180 a 225 270 101 10 Frequency (rad/s) 102 a. Looking at the low frequency behavior, determine its number of poles at origin. Explain. b. Looking at the high frequency behavior, determine the number of excess poles. Explain. C....