If an analog temperature sensor is used with an 8 bit ADC (analog to digital converter) and a 5 volt power source, what is the smallest temperature increment you could measure? That is, what is the resolution here?
The smallest tempreture increment is given by resolution of a ADC
total number of bits used here = 8 bits
power supply = 5Volts
total number of steps= 28 - 1= 256-1=255
step size = resoution of ADC= (power voltage)/(total nomber of steps)
resolution= 5 volts/255= 0.01960Volts= 19.60 mV
smallest tempreture increment corresponding to 19.60mV is the smallest tempreture that can be measured.
If an analog temperature sensor is used with an 8 bit ADC (analog to digital converter)...
1- A12 bits analog to digital converter (ADC) has a sampling rate of IMHz. If the analog signal has a range of 5V, a) How many different digital values can this ADC outputs? (20 POINTS) b) What are the smallest and largest possible outputs of this ADC? c) What is the voltage/bit resolution? d) If an application requires 1u V/bit resolution, how m ADC have? ny bits should the
How many gray levels will an 8-bit ADC (analog-to-digital converter) produce? A) 8 B) 64 C) 256 D) 1024
You are given an analog-to-digital converter (ADC) which is used to convert an input analog signal to a digital signal. The highest frequency present in the input analog signal is 20 Hz. The ADC samples the input analog signal at 1.25 times the minimum required sampling rate. (Note; this ADC “over-samples” the analog input signal; the sampling rate of this ADC is higher than the minimum required sampling rate. The ADC samples at 1.25 times the minimum required sampling rate)....
You need to design for-bit R-2R network digital to analog converter using S k? and io with reference voltage 16 volt. i) Sketch a circuit of this digital to analog converter. i) Calculate the output voltage for an input of 1010, 1101 and 0110 Calculate output voltage resolution
Q1) Digital-to-Analog Conversion The signal shown in the figure below is inserted to a 5-bit ADC converter Considering, the useful range of the converter is 0-3V, draw the values obtained in the ADC output register when the sampling time is a) 1ms, and b) 0.5ms 3 1.5 16 [ms] 8 0 12 a) 4t ms Reg. value 16 ms] 12 4 0 b) 4t 0.5ms Reg. value 16 t [ms] 12 4 8 Q1) Digital-to-Analog Conversion The signal shown in...
An 10-bit analog-to-digital converter (ADC) has a voltage range of 0 to 12 V and a digitization uncertainty of ±1 LSB. What is the maximum uncertainty if the digitization is for a 12 V signal? What is the maximum uncertainty for a 18-bit ADC, and for 43-bit? If this ADC has a conversion time of 73 μs, then what is the highest frequency that can be accurately digitized while satisfying the Nyquist criterion? Answer with proper significant figures.
(a) We have an analogue to digital converter (ADC) described as 8 bit, with a 3V reference and 0V offset. What is the resolution, expressed in millivolts? [2] (b) For an input voltage of 0.6V, what is the digital output value of the ADC described in (a)? Express your answer in both binary and hexadecimal. [3] (c) An industrial oven has a thermometer that outputs a voltage from 0 to 1V for a corresponding range of temperatures of 0 to...
Q2. Answer the following questions a) An ADC converter is required to digitize a -5 to +5 volts analog signal to a resolution of b) The analog input is 0-5 volts and VRH 5, VRL 0. The ADC reading is $24. What is the c) How is the HCS12 ADC powered up? How long must the program delay before using the 10 mV. How many bits are required? analog input voltage for a 10-bit conversion? ADC after powering it up?...
1900) An analog input module uses an A/D converter with 8-bit resolution. The module range is -10 volts to +10 volts. Calculate the module output (digital count) when the input voltage is 3.7 volts. 1) floating point calculation, 2) discrete rounded result (actual digital count), 3) answer-2 minus answer-1 and 4) voltage resolution or smallest detectable change (volts). Assume the minimum digital value is zero. ans:4 thats all that was given to me
sa Date: Apr. 10, 2019 An 8-bit ADC has an input analog range of +5 volts. The analog input signal is t)4 cos (7000Tt). The converter samples the input signal at 8 ksam/s and supplies data to computer 64 kbits/s. The computer re- construct the transmitted signal, x,(C), by using an ideal DAC on the received signal. Determine: (a) The quantizer resolution (or step) (b) Mean squared quantization error (noise) power (c) The folding frequency (d) The reconstructed signal x,...