Answer: -771, -25.7, 5 mW, 99.2 mW
Answer: -771, -25.7, 5 mW, 99.2 mW 4–2 Find the voltage gain vo/vı and the current...
7.2Ω 6Ω 2) For the circuit shown, find (a) the voltage Vo; (b) the power delivered to the circuit by the current source; and (c) the power dissipated in the 10Ω resistor. Vo 300 64Ω 10Ω
1. An amplifier has a voltage gain Av equal to 20. An input voltage v of 150 mVs applied to the input of the amplifier. What is the output voltage vo? Rs 2. For the amplifier in Problem 3, assume the input current i is 2 mA, and the output current io is 10 mA. What is the current gain A, ? Assuming the amplifier as described above has an output resistance is 0 ohms, what is the load resistance...
7 2Ω 6Ω For the circuit shown, find (a) the voltage Vo, (b) the power delivered to the circuit by the current source; and (c) the power dissipated in the 10Ω resistor. 2) 5A Vo 30n 64Ω
HighK_InvOA Rb Rc M Do: Find P, V., i,, P., and the voltage gain of the circuit, i.e. 4. = V. | (Volt) where P, is the power supplied by the input voltage source, V, and P is the power supplied by the output of the opamp. Note that P. is NOT the power absorbed by the load resistor, R. Hints: 1. To calculate P you will need the current supplied by the input voltage source. 2. The power supplied...
Find Vo’ due to the current source Is alone. Vo’=______V
Find Vo” due to the voltage source Vs alone. Vo”=______V
Find Vo due to both sources. Vo=______V
1. Find V, in the network in Fig. 1 using superposition. 1 kΩ 2 kΩ R2 R4 2 kΩζv, R1 6 mA R3ξ 2kΩ Is Vs (+) 12V Figure 1.
[6] Find the current through 9㏀ resistor, n, the output voltage, vo, and the power consumed in the 100Ω load resistor, po. 1k2 Ideal 1.2V vo 100Ω i,
2) In class we considered the circuit shown belovw a) Use the result for the current derived in class to find the voltage Vı across the resistor. b) Find the average power dissipated by the circuit using the equations developed in class and the source voltage Vo(t) and current I(t) c) All the power must be dissipated in the resistor. Check that using just the current and voltage across the resistor gives you the same answer for power dissipation as...
2. A load is connected to a voltage of 1320 volts at 60 Hz. The load dissipates 100 kW with a 0.867 power factor. Specify the capacitance needed to correct the power factor to being 1. 3. Consider a circuit for a single-phase AC power system, where a 200 volt AC voltage source is delivering power to a loads. Find the true power, reactive power and apparent power delivered by 150 mA current (Impedance phase angle 0 = 30°) 3....
electronics question
#3 (5 pts.) A BJT amplifier has the voltage gain of 80, absolute voltage gain of 60, current gain of 40, and source resistance of 1 k2. Find the load resistance (no need to know the circuit or amplifier type).
#3 (5 pts.) A BJT amplifier has the voltage gain of 80, absolute voltage gain of 60, current gain of 40, and source resistance of 1 k2. Find the load resistance (no need to know the circuit or...
What would be the expression for the closed-loop voltage gain A-Vo(t)/v(t) in figure 5 assuing it is an ideal op-am model? 1) 2) What would be the input resistiance of figure 5? 3) What would R, and R2 (from the list below) must be to obtain a voltage gain of A 2.5 1.2 kS2, 1.5 kS2 (2), 1.8 k2, 2.2 k2, 10 k2, 12 k2, 15 k2, 18 k2, 22 k2 +5 V Rs= 1.5 k(2 in(0 5 V VoltageSource...