The output diameter and weight of a hydraulic lift are 89 cm and 1759 kg respectively....
hydraulic lift with a 26.0 cm diameter is supporting the weight of a 2990 kg vehicle (a large car or midsize SUV). (a) What force must be exerted on the 2.05 cm diameter master cylinder of this lift to support the vehicle resting on the other cylinder, the 26.0 cm diameter cylinder of the lift itself? Tries 0/15 (b) What gauge pressure must the hydraulic lines be capable of withstanding?
A hydraulic car lift has an input piston of radius 2.00 cm and negligible weight. The output piston has a radius of 79.2 cm, and the total load on the output plungers is 18000 N. If the car (output piston) needs to be lifted 1.70 m, what volume of non-compressible hydraulic fluid must be pumped into the system?
1-90 A hydraulic lift is to be used to lift a 1900-kg weight by putting a weight of 25 kg on a piston with a diameter of 10 cm. Determine the diameter of the piston on which the weight is to be placed. eigh. 1900 ky 25 kg F:f 10 cm D2 FIGURE P1-90
In a hydraulic lift, the radius of the input piston is 5.0 cm and the radius of the output piston is 30.0 cm. (a) If a force of 20.0 N is applied to the input piston, how much weight can the output piston lift? moves a vertical distance of 0.80 cm, then how much does the input piston move? (b) If the output piston ww.ai d ae
The hydraulic oil in a car lift has a density of 8.17x10^2 kg/m^3. The weight of the input piston is negligible. The radii of the input piston and output plunger are 8.56x10^-3 m and 0.171m, respectively. What input force F is needed to support the 27200-N combined weight of a car and the output plunger, when (a) the bottom surfaces of the piston and plunger are at the same level, and (b) the bottom surface of the output plunger is...
A hydraulic lift is used to jack a 950-kg car 42 cm off the floor. The diameter of the output piston is 17 cm , and the input force is 360 N . What is the area of the input piston? What is the work done in lifting the car 42 cmcm ? If the input piston moves 13 cmcm in each stroke, how high does the car move up for each stroke? How many strokes are required to jack...
What is the largest vehicle (kg) it can lift if the diameter of the output is 29.5 cm ? Answer use 3 sig figs KHw1 PHYS 132 Problem 10.14 Constants The maximum gauge pressure in a hydraulic lift is 18.9 atm 1 atm 1.013 x 105 N/m2
A hydraulic lift has pistons that are 1 cm and 15 cm in diameter. If a force of 180 N is applied to the master cylinder, what is the largest mass that the lift can support?
Pascal’s principle: What force must be exerted on the master cylinder of a hydraulic lift to support the weight of a 1800 kg car resting on the slave cylinder? The master cylinder has a 2.00 cm diameter and the slave has a 25.0 cm diameter. Pascal’s principle: A barber’s chair rests on a hydraulic piston 10 cm in diameter. The input side has a piston with cross-sectional area of 10 cm2 which is pumped on using a foot pedal. If...
A hydraulic lift is used to jack a 940-kg car 42 cm off the floor. The diameter of the output piston is 19 cm , and the input force is 360 N . A) What is the area of the input piston? Express your answer using two significant figures. B)What is the work done in lifting the car 42 cm ? Express your answer using two significant figures. C)If the input piston moves 14 cm in each stroke, how high...