ZuoTi.Pro
Question



November 12, 2019 For the gear reduction system, the load, shear and moment diagrams are shown. Refer to shaft AB with diamet
engineering   Mechanical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

Kf = 1+ q (kt -1). K+ = 2.15 q=0.85 K= = 1+0.85 (2.157). 1+0.85X1-15 1.9773 Kol kas= lta (kts-1) - t 0.85 (2.9-1) . = 1+0.85XDE ASME Critena Mas neidrauge moment. Mm = Ma 1.275 Mm = 2178 - 1708 1.275 Mm = 192.97 N-m. lb-inch 1 Tm - midrange torque. Tfacter of Safety Pos = but ob - Assuming the gears are made up. a osteel. . but = 800 mpa.. Pos = 800 4.96 902 161 ST ES SI

0 0
Add a comment
Know the answer?
Add Answer to:
November 12, 2019 For the gear reduction system, the load, shear and moment diagrams are shown....
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • a. create the FBD, shear, Moment, and torque diagrams for the shaft. B. what is the...

    a. create the FBD, shear, Moment, and torque diagrams for the shaft. B. what is the location of maximum stress (plane of interest for the design)? you may disregard all feometric stress concentration factors. C.what stresses are in existence on the plane of interest? Do not calculate them, what is exists. d. Draw the wave forms for the stresses in existence on the plane of interest. e. you must determine if this shaft will have an infinite life, what failure...

  • Will thumbs up solution. Thanks! Problem 3 (200 pts): For a driven shaft of a gearbox,...

    Will thumbs up solution. Thanks! Problem 3 (200 pts): For a driven shaft of a gearbox, one possible shaft layout is shown in the top figure. Both bearings and the gear will be located against shoulders. The gear and the motor will transmit the torque through the keys. The bearings can be lightly pressed onto the shaft. The left bearing will locate the shaft in the housing, while the right bearing will float in the housing. Shear force, bending moment,...

  • Solve in SI units. A gear reduction unit uses the countershaft shown in the figure. Gear...

    Solve in SI units. A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20ᵒ pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force FB at the pressure angle shown. a) Determine the force FB, assuming the shaft is running at a constant speed. b) Find the magnitudes of the bearing reaction forces,...

  • Extra Credit) A gear reduction unit uses the countershaft shown in the figure. Gear A receives...

    Extra Credit) A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force FB at the pressure angle shown. (a) Determine the force FB, assuming the shaft is running at a constant speed. (b) Find the magnitudes of the bearing reaction forces, assuming the...

  • Question 2 The shaft shown below is rotating at 650 rpm, and it receives 7.5 hp...

    Question 2 The shaft shown below is rotating at 650 rpm, and it receives 7.5 hp through a flexible coupling. The power is delivered to an adjacent shaft through a single helical gear B having a normal pressure angle of 20 degrees and a helix angle of 15 degrees. The pitch diameter for the gear is 4.141 inches (De) and the Tangential (Wu), radial (W) and axial/thrust (W) are shown below on the drawing. The shaft is to be made...

  • Problems 1. (Subtotal: 21 points) A steady torque of 1500 Ibf in is transmitted by a...

    Problems 1. (Subtotal: 21 points) A steady torque of 1500 Ibf in is transmitted by a machined shaft made of steel with an ultimate tensile strength of 100 kpsi. The transverse cross section at the location of a shoulder against which a gear sits is subjected to a bending moment which is a sinusoidal function of time with a maximum of 800 lbf-in. Furthermore, this cross section is the location for the maximum von Mises stress. The smaller diameter at...

  • .Below shalt has two rotating commponents as shown. Solve tor Fa force frst Then resolve the...

    .Below shalt has two rotating commponents as shown. Solve tor Fa force frst Then resolve the load components into y and z components 400 m 25° Gear A. 600-mm dia Gear R, 300-mm dia The details of the stepped shaft is shown below. All of the dimensions in above and below figures are in mm. in x direction between two figures to match locations. Perform a fatigue analysis by assuming that the shaft is made of 1050 CD steel Sut-690...

  • I. The countershaft shown in the Fig Q1 has two spur gears mounted on it with teeth cut wi a 20 pressure angle....

    I. The countershaft shown in the Fig Q1 has two spur gears mounted on it with teeth cut wi a 20 pressure angle. The shaft (grooved) is to be made of cold-drawn AISI 1040 steel havin Sut 779 MPa and S,-593 MPa, an elongation of 19% and HB-262. You are asked to size the shaft for safe operation according to DE-Elliptic criterion by using a factor of safety of 2.5 and a reliability of 99 percent. The stress-concentration factors for...

  • 1. The countershaft shown in the Fig QI has two spur gears mounted on it with teeth cut with a 20 pressure angle...

    1. The countershaft shown in the Fig QI has two spur gears mounted on it with teeth cut with a 20 pressure angle. The shaft (grooved) is to be made of cold-drawn AISI 1040 steel having Sut= 779 MPa and S,-593 MPa, an elongation of 19% and HB-262. You are asked to size the shaft for safe operation according to DE-Eilliptic criterion by using a factor of safety of 2.5 and a reliability of 99 percent. The stress-concentration factors for...

  • You work for a gearbox company and have been charged with helping to design a geared...

    You work for a gearbox company and have been charged with helping to design a geared countershaft for a speed reducing gearbox. The gearbox consists of a compound reverted gear train as shown below and is to be designed for an exact 16:1 speed reduction ratio. The input motor provides 10-horsepower which is carried through the gear train and operates at a speed of 2,000 rpm. You are asked to consider spur gears with a 20° pressure angle and 4...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT