We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Using the given load line and the diode curve, figure out the value of resistance R....
QUESTION 1 l (mA) 3.0 Diode I-V 25 PS 1.5 1.0 0.5 5 Yo (volt) Using the given load line and the diode curve, find the Ip quiescent value approximately in mA's. Choose one of the choices given closest to what you found. Hint: You can find the answer approximately just looking at the two graphs (we call this the graphical method) O approximately 1.5 mA O approximately 1.7 mA O approximately 1 mA approximately 2 mA
DIODE CHARACTERISTICS Objective: The objective of this laboratory is to examine and plot the forward characteristics curve of a p-n junction diode and become familiar with the characteristics of both the p-n junction diode and the light emitting diode (LED). Prelab: Answer the following on a separate sheet of paper. Show your work and box your answers 1. Review the data sheets for the IN4001 p-n junction diode and answer the following a) Determine the maximum forward current and the...
Using MULTISIM SIMULATION PLEASE!!! using multisim please Reversed Vascu Procedure II: Diode Characteristics: 1. Wire the circuit shown in Figure B. 3300 LA Vs Vd = (0-15V) Figure B Diode Characteristics pote Mode is defined as The dy to the dio rent through 10 3. Now reverse the diode then adjust the DC supply as shown in Table 2, Record the corresponding current and diode voltage as in step 2. Table 2 Reversed Bias Diode Characteristics Vs (volt) Va la...
9 Homework 10 P 9.24 9 of 9 Sketch the load line. Plot the points for t that are separated by the step Av 0.5 V Review Consider the circuit shown in (Figure 1). The diode is the LED having the characteristic shown in (Figure 2). Use graphical load ine techniques to solve for f and for the cirouit of (Figure 1 No elements selected i (mA) Figure 1 of2 > 2.5 2 mA 0.5 e (V) 0.0 00 05...
Electronic Devices and Circuits ENGI27907 01 Q2. For the circuit shown in Figure 2, Vi=15V, R-2000, the zener diode is 1N4741A with the characteristics obtained from data sheets given below: a Find the minimum value for the rheostat resistance R., for which the zener diode will still maintain regulated voltage Vin across the load R. b. Discuss the current pass through the zener diode and the voltage across it, if the rheostat is turned to 1200 c. If the no-load...
The silicon diode shown in the given figure is described by ip = I. (ed/- 1) where at T = 300 K, 1. = 250 x 10-12 A, VT = KT 26 mV, vs = Vs + V3 = 4.2V + 110 cos(wt) mV,w = 377 rad/s, and R = 10 ko. The DC operating (quiescent) point Q and the AC small-signal equivalent resistance at Q are as follows: IDQ = 0.548 mA, VDQ = 0.365 V, and ra =...
Problem 2 A 1.5 volt energy source is to used to power a 5 volt, 1 amp load. A buck-boost converter is used for this application. A suitable transistor is found with an on-resistance of 35 mQ, and a Schottky diode is found with a forward drop of 0.5 volts. The on resistance of the Schottky diode may be ignored. The circuit is shown in the following figure. 1 A 100 HH 5 V Load 1.5 V DT T f,...
The load shown in Figure 2.22 consists of a resistance R in parallel with a 2.6. capacitor of reactance X. The load is fed from a single-phase supply through a line of impedance 8.4 + j 11.2 Ω. The rms voltage at the load terminal is 120020° V rms, and the load is taking 30 kVA at 0.8 power factor leading. (a) Find the values of R and X (b) Determine the supply voltage V. 8.4 +j11.2 2 120020 VRTX
2.6. The load shown in Figure 2.22 consists of a resistance R in parallel with a capacitor of reactance X. The load is fed from a single-phase supply through a line of impedance 8.4 + j 11.2 Ω. The rms voltage at the load terminal is 120020° V rms, and the load is taking 30 k VA at 0.8 power factor leading. (a) Find the values of R and X (b) Determine the supply voltage V. 8.4+511.2 Ω 120020° vsh...
A MOSFET and diode is used in a circuit shown in figure. The operating conditions are as follows: Input Voltage = VIN = 42 V, Io = 5A. Switching frequency fs = 400 kHz, Duty-cycle = D = 0.3. Diode Forward Voltage drop = 0.7V. Diode Peak Reverse Recovery Current = IRRM = 2.5 A. ON-state resistance of the MOSFET is RDS (on) = 25 mΩ. VGG as a step voltage between 0V and 10 V. MOSFET timings – Td...