1.
Peak repetiive reverse voltage = 50V
maximum current carrying capacity = 1A ( it withstand peaks up to 30A )
2.
Maximum Full−Cycle Average Forward Voltage Drop VF(AV)= 0.8v
Typical Reverse Current (TJ = 25°C) =0.05 uA
3.
Typical forward drop = 0.93V
For more solution please resbmit question papper with serial number of questions
DIODE CHARACTERISTICS Objective: The objective of this laboratory is to examine and plot the forward characteristics...
Tutorial 2 The data sheet of a certain P-N junction diode specifies a leakage current of 0.25mA at room temperature of 25[]C and 0.05 mA at 100[c. The diode has forward biased constant current of 30A at room temperature. If forward biased current is assumed to remain constant at all temperatures. Calculate the junction internal barrier voltage at room temperature and at 1000C. take 1=1 The data sheet for a silicon diode specifies a forward voltage drop of 2.35V for...
Ctri Question 3 (20 Marks) Lab 1-Zener Circuits and Applications Theory: Zener diode is designed to operate in reverse conduction. Zener breakdown occurs at a precisely defined voltage, allowing the diode to be used as a voltage reference or clipper. While Zener diodes are usually operated in reverse conduction, they may also be operated in cutoff and forward conduction. There are two different effects that are used in "Zener diodes". The only practical difference is that the two types have...
Question 1 1 pts Consider a standard diode shown below. Check all the statements that are true for diodes and diode circuits.ID ip + V- In the forward bias region, the diode current ip is positive. Diodes are made by connecting a p-doped material to an n-doped material, creating a depletion region that causes a barrier to the flow of electricity when the diode is reverse biased. In the non-conducting (or OFF) state of an ideal diode, the diode voltage,...
Using MULTISIM SIMULATION PLEASE!!! using multisim please Reversed Vascu Procedure II: Diode Characteristics: 1. Wire the circuit shown in Figure B. 3300 LA Vs Vd = (0-15V) Figure B Diode Characteristics pote Mode is defined as The dy to the dio rent through 10 3. Now reverse the diode then adjust the DC supply as shown in Table 2, Record the corresponding current and diode voltage as in step 2. Table 2 Reversed Bias Diode Characteristics Vs (volt) Va la...
Design an abrupt Sip+-n junction diode that has a reverse breakdown voltage of 130 V andhas a forward-bias current of 2.2 mA at V = 0.7 volt. Assume tp = l0^-7 s.
An abrupt junction GaAs diode is doped with acceptors on the P-side at a concentration of 1016 cm−3 , donors on the N-side at a concentration of 1017 cm−3 and operated at 300 K. The hole recombination time on the N-side 0.2 µs and the electron recombination time on the P-side is 2 µs. The cross sectional area is 10-2 cm2 a) Calculate the reverse saturation current. b) Calculate the contact potential. e) Calculate the bias voltage needed to obtain...
Problem 4: An abrupt silicon p-n junction diode has the following characteristics. side n-side N-4x 1016cm N1016cm3 n 1000 cm2/V sec 350 cm2/V sec Area A 102cm2 Calculate the following quantities: (a) Reverse saturation hole current component (b) Reverse saturation electron current component. (c) Minority carrier concentrations at the edge of the depletion layer, p(0) and pr(0), for a forward voltage of 0.6 V (d) Electron and hole current for the bias condition of (c). (e) Make a rough sketch...
1. a) State the diode equation and explain the significance of each term. b) Sketch the current - voltage characteristics for a typical silicon diode over the 4 voltage range -2 V to +2 V. Explain how the characteristics would change if the diode was fabricated using germanium. Give an equivalent circuit representation of the device in each case. c) In a silicon diode a current of 200 HA flows when a forward bias voltage of 0.5 V4 is applied...
A silicon PN junction diode is constructed using N-type silicon in which the Fermi level is 100 meV below the conduction band edge and P-type silicon in which the Fermi level is 120 meV above the valence band edge a) What are the majority and minority carrier concentrations on each side of the junction under thermal equilibrium? b) What is the value of the built-in voltage? c) Determine the width of the depletion region on both sides of the junction...
1. Consider a p*n silicon diode at T-300 K with doping concentrations of N 10 cin and N-101 cm-3. The minority carier hole diffusion coefficient is D 12 cm2/s and the minority carrier hole lifetime is po 10-7 s. The cross sectional area is A 10- cm2. Calculate the reverse saturation current and the diode current at a forward-bias voltage of 0.50v A germanium p* n diode at T-300 K has the following parameters: Na 108 cm-3 N,--1016 cm", ,...