STEEL STRUCTURE

Question

Question

Screenshot (52).png

Answer 1

Similar Homework Help Questions

Problem of steel structure

A C9 x 20 tension member is connected with 9/8 inch-diameter bolts as shown in figure FY= 50 Ksi and Fu = 70 Ksi. The member is subjected to the following service deal load = 36Kips and live load = 110 kips. Analyze the member for adequacy with respect to applied load using ASD and LRFD.
1. A steel plate has been welded to a steel structure using fillet welds. It needs...

1. A steel plate has been welded to a steel structure using fillet welds. It needs to support a weight with very little chance of yielding. What maximum weight, F, can the welds support, with a safety factor of 4.0 on yield? Remember that you need to treat the weld as a "beam." E60 weld rod used: Su = 60 ksi Sy = 48 ksi 3 in.
The structure that is typically produced after a eutectoid steel is normalized is:

The structure that is typically produced after a eutectoid steel is normalized is: 100% bainite 100% g 100% martensite 100% fine pearlite 100% coarse pearlite 100% ferrite 100% cementite

The shown vertical steel column is used to support a structure

The shown vertical steel column is used to support a structure. Assume the column to be fixed at its top and pinned at its bottom. A 15 kN load is applied at an eccentric distance of 250 mm as shown. determine the maximum stress in the column. E=210 GPa, Yield stress =250 MPa. A=4960 mm2 d=363 mm Ixx=102(106) mm4
Please answer the following Steel Structure Design question. You may need to referance a steel de...

Please answer the following Steel Structure Design question. You may need to referance a steel design manual. A3 sbelts are used in a Cder yield, rupture CU Lo in is e and block skar ropture Determin the design tension by LRFD. (25%) Block Shepr AI し5" A3 sbelts are used in a Cder yield, rupture CU Lo in is e and block skar ropture Determin the design tension by LRFD. (25%) Block Shepr AI し5"
Two mild steel tie bars for a bridge structure are to be joined by thickness of...

Two mild steel tie bars for a bridge structure are to be joined by thickness of the tie bar is 20 mm and carries a tensile load of 400 kN. Design the joint if the allowable stresses are : o, = 90 MPa ; t = 75 MPa and o = 150 MPa. a double cover butt joint. The 14. Assume the strength of rivet in double shear to be 1.75 times that of in single shear 150 mm ;...

A steel with the BCC crystal structure containing 0.0013 % N is nitrided for 20 h...

A steel with the BCC crystal structure containing 0.0013 % N is nitrided for 20 h so as to obtain N concentration of 0.0613 % at the depth of 0.5 mm from the surface. If the nitrogen content at the steel surface is 0.1%, determine the temperature at which the treatment was carried out.
A building made with a steel structure is 650 m high on a winter day when...

A building made with a steel structure is 650 m high on a winter day when the temperature is 0° F. How much taller (in cm) is the building when it is 100° F? (The linear expansion coefficient of steel is 11 10-6 (°C)-1.) 36 46 40 65 71
In a hybrid truss structure, made of steel and wood elements, we want to check their...

In a hybrid truss structure, made of steel and wood elements, we want to check their stress state. Elements can be either in compression or in tension. By observing the truss, one finds that: • 65% of the elements are in compression. • 30% of the elements in compression are in steel. • 60% of the elements in tension are in steel. An element is selected at random. a) Find the probability that: с : the element is in compression....

A 25mm diameter steel rod 1.5m long is being used in a rigid structure. For this...

A 25mm diameter steel rod 1.5m long is being used in a rigid structure. For this steel the Ultimate Tensile Stress is 410 MPa Young’s Modulus is 200 GPa The rod is to be subjected to a tension load of 40 kN. Design requirements are that the rod cannot extend by more than 0.5 mm and that there is a Factor of Safety of 5 for the tensile stress. Determine whether or not the rod is adequate for the task:...